Chemistry

1. Why cannot NaOH be used as primary standard for HCl?
2. Aside from carbonates, what other compounds can be analyzed using the double indicator method? What are the requirements for a sample to be analyzed using the double indicator method?
3. what is a carbonate error? Explain the cause of carbonate error and its effect on the calculated values obtained in standardization and sample analysis.

1. Even if we could buy PURE NaOH, it wouldn't stay that way due to absorbtion of CO2 from the air. That portion of CO2 would make Na2CO3. So the NaOH must be standardized using a primary standard such as potassium hydrogen phthalate.
2,3,and 4. I'm sure all these (including #1) are discussed in your text. I shall be happy to critique your thoughts.

for my second question, my idea is that double indicator method is applicable to all polybasic compounds. Is this true? If this is, then double indicator method is applicable to phosphates, oxalates, sulfates, arsenates, etc. Am I right?
As for my third and fourth question, I really have no idea about carbonate error. What is this all about. I have tried searching for an answer in the internet but I can't find any explanations about this error.


Second Question:

BTB works. PH Paper

The double indicator method is applicable to selected mixtures and selected dibasic and/or tribasic acids.
What text are you using and what course are you taking? Perhaps I can tell you what to read.

I am using "Fundamentals of Analytical Chemistry" by Skoog, West, Holler and Crouch. I am a Chemistry major

I suspected that but I wanted to confirm to make sure.
Look in the index under "sodium hydroxidei solutions, preparation and standardization of". Within that section that is a subsection on "The Effect of carbon dioxide upon standard base solutions." My copy of Fundamentals of Analytical Chemistry by Skoog, West, and Holler is the sixth edition; threrefore, I can't give you the exact page. However, my copy also has "carbonate error" listed in the index. For answers to double titrations etc look in the index under "Carbonate-hydrogen carbonate mixtures, analysis of". In that section there are a number of side column notes and references to figures in chapter 11 that talks about the mixtures that may be separated and some of the problems associated with them. Your text and mine won't have the same page number or perhaps not even the same chapter number; however, all of the answers you seek are in those sections I noted. Post specific questions but tell us exactly what you don't understand about them.

Thank you very much DrBob22!!!

From UP Diliman kb?

  1. 👍 0
  2. 👎 0
  3. 👁 67
asked by Chin

Respond to this Question

First Name

Your Response

Similar Questions

  1. chem

    Quantitative analysis of soda ash by double indicator *why there is a need to boil distilled water in the preparation of base solutions? *why a mixture of NaOH and NaHCO3 is incompatible? *why there is a need t o boil the solution

    asked by tintin on December 22, 2008
  2. chemistry

    HCl is titrated with NaOH. When doing the titration, some of the NaOH splashed onto the inside surface of the Erlenmyer flask, and you forgot to rinse it into your sample. Would the systematic error be falsely high, low, or

    asked by bria on September 17, 2006
  3. Chemistry

    A titration setup was used to determine the unknown molar concentration of a solution of NaOH. A .025 M HCl solution was used as the titration standard. The following data were collected. Trial 1 Trial 2 Trial 3 Initial NaOH Buret

    asked by Anonymous on December 9, 2018
  4. Chemistry (molarity) (sorta an emergency)

    I'm doing a titration lab and writing a lab report where I'm sort of stuck on how exactly to find the concentration of HCl. These are the following info I have from the lab, Equation: HCl(aq)+NaOH(aq)-> H2O(l)+NaCl(aq) -Calculated

    asked by Ray on November 13, 2016
  5. chemistry

    A student prepares a solution of hydrochloric acid that is approximately 0.1 M and wanted to determine its precise concentration. A 25.00 mL portion of the HCl solution is transferred to a flask, and after a few drops of indicator

    asked by walter on June 14, 2015
  6. chemistry

    So I did a titration lab at school with NaOH and HCl. i have to find: - volume used, NaOH - Moles of NaOH - Moles of HCl -Volume used unknown HCl - Molarity of HCl solution My concentration of NaOH stock solution was 0.100 mol/lL

    asked by julie on January 4, 2015
  7. chemistry

    If it requires 30.0 milliliters of 1.2 molar HCl to neutralize 20.0 milliliters of NaOH, what is the concentration of the NaOH solution? Balanced equation: NaOH + HCl NaCl + H2O 0.60 M NaOH 0.80 M NaOH 1.3 M NaOH 1.8 M NaOH

    asked by Magan on June 22, 2011
  8. Chemistry

    I need help plugging these in. I didn’t understand what DrBoB222 meant 2.A student starts with a titration by placing 30.0mL of 0.25M NaOH into a flask with 3 drops of phenolphthalein. The student then titrated to the endpoint

    asked by Samantha on April 12, 2018
  9. chem

    HCl is a strong acid and ionizes 100%. NaOH is a strong base and ionizes 100%. We have no way of knowing the pH of HCl + H2O because the problem doesn't state the amount of HCl added or the concentration of HCl. For the NaOH + HCl

    asked by DrBob222 on May 15, 2007
  10. chemistry

    The titration of HCl with NaOH is represented by the equation HCl(aq) + NaOH(aq) → NaCl(aq) + H2O(l) What volume of 0.100 M HCl is required to titrate 50.0 mL of 0.500 M NaOH?

    asked by kathy on December 6, 2011
  11. chemistry- pH, neutralization

    What volume of NaOH was required to have neutralized the HCl. HCl + NaOH --> H2O + NaCl There no other information given in the problem except in later questions like the NaOH had 0.1 M and that there was 50.00 mL of HCl.

    asked by laura on February 2, 2012

More Similar Questions