# Physics

The cylindrical bar in the figure has a total length L=1.2 m, a diameter d=15 mm, and is confined by fixed supports at the walls A and B. A concentrated axial load FC=30 kN is applied to the bar at point C as indicated in the figure, with LAC>LBC. The bar is homogenous with Young’s modulus E. The material will fail if the magnitude of axial stress in the material exceeds σf=226 MPa.

1. 👍 0
2. 👎 0
3. 👁 144
1. I do not see a question here. Whether or not the bar fails will depend upon where the axial load is placed.

http://www.engineersedge.com/beam_bending/beam_bending19.htm

1. 👍 0
2. 👎 0
posted by drwls

## Similar Questions

1. ### physic

The composite bar BCD in the figure is composed of an inner aluminum cylindrical core of length 2l=2m and radius R=1cm and a sleeve of steel of length L=1m and thickness R=1cm surrounding the aluminum core in the CD section of the

asked by asas on May 1, 2013
2. ### Physic

The composite bar BCD in the figure is composed of an inner aluminum cylindrical core of length 2L=2 m and radius R=1 cm, and a sleeve of steel of length L=1 m and thickness R=1 cm surrounding the aluminum core in the CD section

asked by Me on May 7, 2013
3. ### mechanical properties of materials

A cylindrical steel bar is required to support a load of 650 N. the required bar must be 0.17 m in length and must not deform by more than 0.015 mm. given that the Young's modulus of steel is 210 GPa, calculate the minumum

asked by dmkp on January 28, 2013
4. ### mechanical properties of materials

A cylindrical steel bar is required to support a load of 650 N. the required bar must be 0.17 m in length and must not deform by more than 0.015 mm. given that the Young's modulus of steel is 210 GPa, calculate the minumum

asked by dmkp on January 28, 2013
5. ### Mechanics

The cylindrical bar in the figure has a total length L=1.2 m, a diameter d=15 mm, and is confined by fixed supports at the walls A and B. A concentrated axial load FC=30 kN is applied to the bar at point C as indicated in the

asked by AMK on May 12, 2013
6. ### Physics

Composite bar with end load (two segments) The composite bar BCD in the figure is composed of an inner aluminum cylindrical core of length 2L=2 m and radius R=1 cm and a sleeve of steel of length L=1 m and thickness R=1 cm

asked by helpless on April 30, 2013
7. ### math

determine an accurate figure for the labour element ( labour hours per tonne) for fixing of (a) 10 mm, and (b) 16 mm reinforcing bar ( which, together , make reinforcement cages for the unit).it is a well established fact that the

asked by emy on September 30, 2011
8. ### math

A metal solid made up of a cylindrical bar fixed onto a cube. The cylindrical bar fixed onto a cube. The cylindrical bar is 20 cm long and has a diameter of 7 cm. Each side of the cube is 9 cm long. The surface of the solid was

asked by king on January 9, 2015
9. ### Physics

The bar in the figure has constant cross sectional area A. The top half of the bar is made of material "1" with mass density ρ1, and Young’s modulus E1. The bottom half of the bar is made of material "2" with density ρ2 and

asked by HELP NOW on May 5, 2013
10. ### Physics

The bar in the figure has constant cross sectional area A. The top half of the bar is made of material "1" with mass density ρ1, and Young’s modulus E1. The bottom half of the bar is made of material "2" with density ρ2 and

asked by AK on May 5, 2013

More Similar Questions