A liquid of density 1354 kg/m^3
flows with speed 2.45 m/s into a pipe of diameter 0.29 m. The diameter of the pipe decreases to 0.05 m at its exit end. The exit end of the pipe is 7.82 m lower than the entrance of the pipe, and the pressure at the exit of the pipe is 1.4 atm.
A) What is the velocity v2 of the liquid flowing out of the exit end of the pipe? Assume the viscosity of the fluid is negligible and the fluid is incompressible. The acceleration of gravity is 9.8 m/s^2
and Patm = 1.013 × 10^5 Pa. Answer in units of m/s.

B) Applying Bernoulli’s principle, what is the pressure P1 at the entrance end of the pipe? Answer in units of Pa

I found A) to be 82.41800 m/s and this is correct. Can someone help me with B)?

  1. 👍
  2. 👎
  3. 👁
  1. (a) continuity equation:
    v₂=v₁(d₁/d₂)² =82.4 m/s.
    p₁=1.4 atm = 141855 Pa
    h₂-h₁ =-7.82 m
    Bernoulli Equation
    p₁+ρ‧ν₁²/2 +ρ‧gvh₁ = p₂+ρ‧ν₂²/2 +ρ‧gvh₂
    p₁ = p₂+ρ(ν₂²-ν₁²)/2 +ρ‧g(h₂-h₁)=
    =141855 +1354‧(82.4² -2.45²)/2 -1354‧9.8‧7.82 =
    = 4838223.9 Pa = 47.7 atm

    1. 👍
    2. 👎
  2. p₁+ρ‧ν₁²/2 +ρ‧g‧h₁ = p₂+ρ‧ν₂²/2 +ρ‧g‧h₂
    p₁ = p₂+ρ(ν₂²-ν₁²)/2 +ρ‧g(h₂-h₁)=
    =141855 +1354‧(82.4² -2.45²)/2 -1354‧9.8‧7.82 =
    = 4838223.9 Pa = 47.7 atm

    1. 👍
    2. 👎
  3. it tells me that its incorrect

    1. 👍
    2. 👎

Respond to this Question

First Name

Your Response

Similar Questions

  1. Physics

    Please someone help..A horizontal pipe 10.0cm in diameter has a smooth reduction to a pipe 5.0cm in diameter. If the pressure of the water in the large pipe is 80000Pa and the pressure in the small pipe is 60000Pa at what rate

  2. Physic

    1. Water at a pressure of 3.00 x 10 5th Pa flows through a horizontal pipe at a speed of 1.00 m/s. The pipe narrows to one-fourth its original diameter. What is the speed of the flow in the narrow section? Not sure was

  3. Physics

    Water flows at a speed of 15 m/s through a pipe that has a radius of 0.40 m. The water then flows through a smaller pipe at a speed of 45 m/s. What is the radius of the smaller pipe?

  4. physics

    The water supply of a building is fed through a main entrance pipe 6cm in diameter. A 2cm diameter faucet tap positioned 2m above the main pipe fills a 25 liter container in 30s. (a) What is the speed at which the water leaves the

  1. physics, buoyance

    Water flows at a rate of 25L/min through a horizontal 8.0-cm-diameter pipe under a pressure of 5.7Pa . At one point, calcium deposits reduce the cross-sectional area of the pipe to 40cm2 . Part A What is the pressure at this

  2. physics

    A round pipe of varying diameter carries petroleum from a wellhead to a refinery. At the wellhead the pipe's diameter is 56.3 cm (0.563 m) and the flow speed of the petroleum is 13.5 m/s. At the refinery the petroleum flows at

  3. physics

    Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in figure below, the pressure is P1 = 1.75X104 Pa and the pipe diameter is 6.00 cm. At another point y = 0.250 m higher, the pressure is P2 =

  4. Physics

    Water (density = 1.0 × 103 kg/m3) flows through a horizontal tapered pipe. At the wide end its speed is 4.0m/s and at the narrow end it is 5.0 m/s. The difference is pressure between the two ends is:

  1. Physics

    The water flowing through a 1.9 cm (inside diameter) pipe flows out through three 1.3 cm pipes. (a) If the flow rates in the three smaller pipes are 24, 18, and 13 L/min, what is the flow rate in the 1.9 cm pipe? (b) What is the

  2. physics

    1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm? The pressure at the

  3. calculus- URGENT PLEASE!!

    Consider that there is a container having the shape of an inverted cone. It has a base- diameter of 24cm and the height is twice as its diameter. The inverted cone contains the liquid and due to a small leakage at the bottom end,

  4. Math

    A length of metal pipe has a circumference of 2.5 inches. the pipe is 1/16 inches thick. a gas fitter needs to know the inside diameter of the pipe to calculate the gas pressure. What is the total diameter of pipe including metal?

You can view more similar questions or ask a new question.