physics

A circular plate of uniform thickness has a diameter of 56cm.A circular portion of diameter 42cm is removed from one edge of the plate .find the position of the center of mass of the remaining portion.

  1. 👍 4
  2. 👎 0
  3. 👁 1,078
  1. The removed portion has 3/4 the diameter and 9/16 of the area and mass M of the full circular (56 cm dia) plate.

    Measure CM location from the center of the larger full circle. The center of the cutout circular hole is 7 cm from the center of the large circle

    [M - (9/16)M]*x = M*0 - (9/16)M*7
    (7/16)x = -63/16
    x = 63/7 = -9.0 cm

    The CM is 9 cm from the center of the large circle, in the opposite direction from the center of the removed circle

    1. 👍 0
    2. 👎 7

Respond to this Question

First Name

Your Response

Similar Questions

  1. Math

    For any circle, which ratio is equal to the number π? Select all that apply. ***A. Circumference ------------------- Diameter B. Circumference ------------------- Radius ***C. Circumference ------------------- 2 Times Radius D.

  2. Maths

    An iron pipe of internal diameter 2.8 cm and uniform thickness 1 mm is melted and a solid cylindrical rod of the same length is formed. Find the diameter of the rod.

  3. Math - Please check!

    1. Find the circumference of a circle with a diameter of 11 cm to the nearest hundredth. Measurement formula C = pi x diameter a. 34.54 cm *** b. 17.27 cm c. 5.5 cm d. 33 cm 2. Which of the following is an irrational number? a.

  4. Physics

    A ball and a thin plate are made from different materials and have the same initial temperature. The ball does not fit through a hole in the plate, because the diameter of the ball is slightly larger than the diameter of the hole.

  1. Physics

    A circular hole in an aluminum plate is 2.725 cm in diameter at 0.000 degrees celsius. What is its diameter when the temperature of the plate is raised to 100.0 degrees celsius?

  2. physics

    In an experiment to estimate the diameter of an oil molecule,an oil drop of diameter 0.05cm spreads over a circular patch whose diameter is 20cm. ¡)determine the volume of the oil drop.

  3. physics

    For this problem use the Uniform circular motion mode of the simulation. (a) Given the limits on the sliders in the simulation, what is the maximum possible speed that can be achieved in "Uniform circular motion" mode? .25 m/s For

  4. math

    An architect is designing a circular opening 16 feet in diameter to make room for a spiral staircase. If pi = 3.14, what will the circumference of the circular opening be? 50.24 feet

  1. maths

    a circular section 8.0cm in diameter is marked out 9f a rectangular plate 20cm ×18cm in dimensions. if the centre of the section marked out lie on the diagonal abd is 7.0cm from the centre of gravity of the rectangular plate,

  2. math

    A cross section of a hollow circular pipe shows that its inner diameter is 2 1/10 inches and that the pipe is 3/5 inch thick. What is its outside diameter?

  3. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place.

  4. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place.

You can view more similar questions or ask a new question.