statics and strengths

A cantilever beam member made from steel with hollow circular cross section experiences an axial load of 300 KN (F1), and a vertical load of 200 kN (F2) as shown in the following figure. The beam is 300mm long and fixed on one end.

  1. 👍 0
  2. 👎 0
  3. 👁 163
  1. We don't see the loading diagram.

    See more detailed response at:
    http://www.jiskha.com/display.cgi?id=1344099068

    1. 👍 0
    2. 👎 0

Respond to this Question

First Name

Your Response

Similar Questions

  1. Solid Mechanics

    A cast iron block of 5Cm^2 cross section carries an axial compressive load of 50KN.Calculate the magnitude or normal and shear stresses on a plane whose normal is inclined at 30 deg.to the axis of the block,also determine the

    asked by Devi on August 3, 2012
  2. solid mechanics

    Find the Euler's crippling load for a hollow cylindrical steel column of 3.8 mm external diameter and 2.5 mm thick. Take length of the column as 2.3 m and hinged at its both ends crippling load by Rankine's formula. Using

    asked by ripon on July 31, 2013
  3. strength of materials

    1.a concentrated load p is applied at the end of cantilever.the crosssection of the beam is a square of side "a" and with a hole of diameter "a/2" then deflection at the tip of beam is?lengh of beam is L.

    asked by venkeatesh vanigandla on May 18, 2014
  4. Statics

    A rectangular beam, with cross-sectional width b, height h, Young's modulus Erect, has the same flexural rigidity as a circular beam with the same cross-sectional area. What is the Young's modulus, Ecirc, of the circular beam in

    asked by qwerty on October 23, 2014
  1. Statics

    A cantilever beam, made of a material with a Young's modulus, E with a rectangular cross section with a moment of inertia I, is under a uniformly distributed load, q, across the length L of the cantilever at a point load P at the

    asked by qwerty on October 23, 2014
  2. Materials Science

    A 3-point bending test is performed on a simply supported beam of length L=4m and of rectangular cross-section, with width b and height h. For a central load of 10kN, draw the bending moment and shear force diagrams for the beam.

    asked by qwerty on October 17, 2014
  3. physics

    Comic-book superheroes are sometimes able to punch holes through steel walls. (a) If the ultimate shear strength of steel is taken to be 3.00 x 10^9 Pa, what force is required to punch through a steel plate 1.90 cm thick? Assume

    asked by anthony on February 1, 2013
  4. Algebra

    The maximum load a beam will support varies directly with the square of the diagonal of the beam's cross section.A beam with diagonal 6 inch will support a maximum load of 108 pounds. What load will a beam with a 10 inch diagonal

    asked by Keonn'a on October 29, 2017
  1. Mechanical behavior

    The television coverage of the World Series showed several remarkable slow-motion views of the deflection of the bat as it hit the ball. Major league wood baseball bats are made of ash. A typical major league bat has a length of

    asked by please HELP on November 11, 2015
  2. Mechanical behavior

    An atomic force microscope cantilever, of rectangular cross section, has a length, l, of 200μm, a width, b, of 20μm and a depth, h, of 1μm. It is made of silicon nitride, which has a Young's modulus, E, of 300GPa. What is the

    asked by HELP on November 8, 2015
  3. Mechanical Behavior of Materials

    The television coverage of the World Series showed several remarkable slow-motion views of the deflection of the bat as it hit the ball. Major league wood baseball bats are made of ash. A typical major league bat has a length of

    asked by zxcv on November 8, 2014
  4. Math

    an arch of a bridge is made by bending a steel beam into the shape of a semi circle, if the span (diameter) of the arch is 20m, use the value 3.14 for π to find the length of the steel beam to the nearest meter

    asked by Simon on June 14, 2018

You can view more similar questions or ask a new question.