Chemistry

A student completes titration by adding 12.0 mL of NaOH(aq) of an unknown concentration to 16.0 mL of 0.15M HCl(aq). what is the molar concentration of the NaOH(aq)?

  1. 👍 0
  2. 👎 0
  3. 👁 705
  1. The easy way to do this is
    mL NaOH x M NaOH = mL HCl x M HCl

    This equation works only when the reactants are 1:1 in the equation as is the case with HCl and NaOH.
    NaOH + HCl ==> NaCl + H2O

    1. 👍 1
    2. 👎 0

Respond to this Question

First Name

Your Response

Similar Questions

  1. Chemistry

    A student is given a sample in lab which contains one of the ions listed below. After adding a few drops ofsolution to part of the unknown sample, the student got a greyish precipitate. After adding a few drops ofsolution to

  2. chem TITRATION

    1. If a student fails to remove a large air bubble in the buret before beginning the titration, what will be the effect on the volume of titrant required to reach the titration endpoint? A. The student will record a volume that is

  3. chemistry

    CH3NH2(aq)+H2O(l)=>CH3NH3+(aq)+OH-(aq) Kb=4.4 x 10^-4 Methylamine, CH3NH2, is a weak base that reacts with water according to the equation above. A student obtains a 50.0 mL sample of a methylamine solution and determines the pH

  4. Chemistry

    The bubble in the tip of the buret is not removed prior to performing the NaOH standardization. Will the reported concentration of the NaOH be greater than, less than, or equal to the true concentration of the NaOH if the bubble

  1. Chemistry

    Titration of an Unknown Acid... What effect on the molar mass of the unknown acid would each of the following have... Would it make the calculated molar mass high, low, or would it have no effect? 1. Adding 5 drops of

  2. CHEMISTRY PLEASE HELP

    a) How will the concentration of NaOH be affected if during the titration some of the solid potassium hydrogen phthalate was spilled during the transfer? Will the concentration of the standardized NaOH increase, decrease, or have

  3. Chemistry

    If 32.6 mL of 0.240 M oxalic acid are required to titrate 48.9 mL of unknown sodium hydroxide: How many moles of acid are used in the titration? How many moles of base are used in the titration? What is the molarity of the unknown

  4. Chemistry

    40.0 ml of an acetic acid of unknown concentration is titrated with 0.100 M NaOH. After 20.0 mL of the base solution has been added, the pH in the titration flask is 5.10. What was the concentration of the original acetic acid

  1. Chem

    A 20.00−mL sample of an unknown HClO 4 solution requires titration with 22.92mL of 0.2200M NaOH to reach the equivalence point. What is the concentration of the unknown HClO 4 solution? The neutralization reaction is: HClO 4

  2. chemistry

    PLEASE NOTE: Titration requires several steps in order to obtain exact results. The procedures described in this lab assume that you have already done the TITRATION TUTORIAL and are familiar with the technique. 1. Prepare the NaOH

  3. Chemistry

    We will calculate the amount of acid to use in each titration. Assume that you are using 0.0512 M NaOH(aq). A good volume of NaOH(aq) to use per titration is 15 mL. From this molarity and volume, the moles of NaOH can be

  4. Chemistry

    A student titrated 1.852 g of a mixture containing potassium hydrogen phthalate, KHP....? A student titrated 1.852 g of a mixture containing potassium hydrogen phthalate, KHP, with 0.163 M NaOH solution. She recorded an initial

You can view more similar questions or ask a new question.