chem

In the lab, you're handed a test tube with sodium chloride dissolved in water. You add aqueous barium carbonate to the tube. What are your observations?

Thanks

  1. 👍 0
  2. 👎 0
  3. 👁 84
asked by lena

  1. BaCO3 + NaCl ==> no reaction.

    1. 👍 0
    2. 👎 0
    posted by DrBob222

Respond to this Question

First Name

Your Response

Similar Questions

  1. Solubility/English

    Ok so I have this procedure to rewrite in past tense passive voice please help me out here I have alot ofthings to do with this lab...your help isgreatly appreciated. Thankyou! 1) Set up a hot-water both by placing th 250/400mL

    asked by Lori on February 17, 2013

  2. Chemistry

    1. Take a clean test tube from the Glassware shelf and place it on the workbench. Add 1 mL your mystery solution to the test tube. 2. PRECIPITATION BY NaC2H3O2(aq) (a) Add 2 mL of sodium acetate solution to the test tube. (b) If a

    asked by annonomus on August 11, 2010

  3. Extraction

    Lab..again 0.050g benzoic acid/succinic acid/sodium benzoate. -choose 1 and put 0.050g of that compound into 5ml conical vial -add 2ml methylene chloride and 2ml water -cap vial and shake until all solid is dissolved. -let

    asked by ~christina~ on September 12, 2007

  4. Chemistry

    Hi, I have few questions from a chemistry lab that i did, 1) I'm not sure whats the point of heating a nitrate (NaNO3) 2) I'm not sure why you add NaOH to NaNO3 after it has dissolved in water 3) I'm not sure why do we have to

    asked by Sherlique on December 20, 2016

  5. Chemistry

    You have 20mL of a solution of concentration 0.015mg/mL of x in test tube #1. Prepare serial dilutions of your stock solution, and calculated the concentration of x as follows: Add 10mL of distilled water and 10mL of stock

    asked by Jon on November 3, 2010

  6. Chemistry 12

    Hello fellow comrades, I was assigned the sulphur clock reaction lab and I'm a tad bit confused by it. Anyway, here's the lab procedure: 1. take 5 test tubes, labeled a,b,c,d and e. accurately measure out 10.0 ml of .20M sodium

    asked by TaeYeon on October 6, 2010

  7. Science/CHEM

    Part 1 Chapt 4 1. You dissolve 157.1 g of ammonium nitrate in a 250 mL volumetric flask and add water to the mark (call this solution A). You take 30 mL of solution A and place it in a 100 mL volumetric flask and add water to the

    asked by Kelsey on September 28, 2008

  8. Chemistry

    24. Identify a source of error for the experimental design of the cobalt(II)chloride system In the experiment, there were three test tubes. All of them contained cobalt(II)chloride. Test tube 1 was the constant, therefore, did not

    asked by need helpp on May 26, 2018

  9. chem 1

    if 58.44 g of sodium chloride is dissolved in 0.5 liter of water what is the molarity of the sodium chloride solution? The molar mass of sodium chloride is 58.44 grams per mole.

    asked by don on November 22, 2012

  10. Chemistry

    PRECIPITATION BY NaC2H3O2(aq) (a) Add 2 mL of sodium acetate solution to the test tube. (b) If a white precipitate forms at the bottom of the test tube, decant the remaining liquid into another clean test tube and retain the

    asked by stacy on August 12, 2010

More Similar Questions