You wish to make 1L of sterile lysis buffer soln. that is 10mM Tris-EDTA (pH 8) and 2% SDS. You have plenty of the following stock solns.: 2M Tris-EDTA (pH 8) and 20% SDS. However, SDS cannot be autoclaved and must be added to the soln. after autoclaving is done. Assume that the diluent is dI water.

  1. 👍 0
  2. 👎 0
  3. 👁 244

Respond to this Question

First Name

Your Response

Similar Questions

  1. Chem 2

    A 100-mL sample of water is titrated with EDTA solutions in problem 2. The same amount of Mg2+ is added as previously, and the volume of EDTA required is 31.84mL. What volume of EDTA is used in titrating the Ca2+ in hard water?

  2. chemistry

    25.00 mL aliquots of the solution from Part 1 are titrated with EDTA to the Eriochrome Black T end point. A blank containing a small measured amount of Mg2+ requires 2.60 mL of the EDTA to reach the end point. An aliquot to which

  3. Science

    C6H5NH2 + H2O C6H5NH3+ + OH- 1. Aniline, a weak base, reacts with water according to the rxn above. a. A sample of aniline is dissolved in water to produce 25.0 ml of a .10 M soln. The pH of soln is 8.82. What is Kb for this

  4. biochemistry with more info that was needed

    Calculate the weight of the buffers you will use to make the buffers for Part A for all the buffer possibilities listed under procedures in Part A, step 1. In other words, how many grams do you need to make 100 mL of a 0.1 M

  1. Biochemistry

    How do you prepare 100 mL of a 0.1 M TRIS-HCl buffer with a pH 7.4 using solid TRIS base (MW 121.1) and 1 M hydrochloric acid? I started with pH=pKa + log ([Tris]/[Tris+] [Tris]/[Tris+]= 10^(7.4-8.06]=0.219 so 0.219:1 ratio with

  2. Chemistry - acid base

    What volume of 10.0 M NaOH is needed to prepare a buffer with a pH of 7.79 using 31.52 g of TrisHCl? ( Tris. At 25 ∘C, Tris has a pKb of 5.91 ) a) The buffer from Part A is diluted to 1.00 L. To half of it (500. mL), you add

  3. Bio

    How much solute is required to make 600mL of a 0.4 M solution of Tris buffer? FW of Tris Buffer= 121.1g Work: Molarity equation= moles of solute/ liters of solution Step 1: 121.1 g / 121.14 g/mol TB = 0.9996 mol TB Step 2:

  4. Biochemistry

    Calculate the amount (in grams) of Tris Base needed to make 1L of 0.01M Tris buffer? Tris Base=121.4 g/mol

  1. Chemistry

    A 50.0 mL sample containing Cd2 and Mn2 was treated with 49.1 mL of 0.0700 M EDTA. Titration of the excess unreacted EDTA required 17.5 mL of 0.0300 M Ca2 . The Cd2 was displaced from EDTA by the addition of an excess of CN–.

  2. chemistry

    An enzyme-catalyzed reaction is carried out in a 50-mL solution containing 0.1 M TRIS buffer. The pH of the reaction mixture at the start was 8.0. As a result of the reaction, 0.002 mol of H+ were produced. What is the ratio of

  3. Chemistry

    Calculate the pH of a solution prepared by dissolving 10.0 g of tris(hydroxymethyl)aminomethane ("tris base") plus 10.0 g of tris hydrochloride in 0.250 L of water. (a) What will be the pH if 10.5 mL of 0.500 M NaOH is added?

  4. chemistry

    From a 1M Tris solution, how is a 400ml of 0.2 M Tris prepared? I have no idea where to start

You can view more similar questions or ask a new question.