# chemistry

What is the molarity of the solution that results when 60g NaOH is added to enough water to make 500mL solution?

1. 👍 0
2. 👎 0
3. 👁 45
asked by magguy

## Similar Questions

1. ### science

an unknown molarity of HCl acts as an analyte.50mL of it is placed into a conical flask ans a 0.1M of solution of NaOH was used as a reagent. The endpoint is pH=7, with a pKa of 6.5 chosen.The colour of the solution changed when

asked by constance modongo on October 16, 2018
2. ### chemistry

A 2.5 g sample of NaOH (Mw = 40.00) was dissolved in water to give a solution of final volume 250 cm3. (i) With reasons, state whether NaOH is a strong or a weak base. Give the conjugate acid of NaOH and decide whether this

asked by LUx on April 21, 2013
3. ### Chemistry

Calculate the molarity of the H2SO4 solution if 17.45 mL of NaOH was necessary to reach the endpoint of titration. The molarity of the NaOH solution was 0.425 M and 26.30 mL of H2SO4 was added to the Erlenmeyer flask. H2SO4(aq) +

asked by Audrey on February 25, 2017
4. ### Chemistry

Consider the titration of 50 mL of 0.250 M HCl with 0.1250 M NaOH. Calculate the pH of the resulting solution after the following volumes of Na OH have been added. a) 0.00 mL b) 50.00 mL c) 99.90 mL d) 100.00 mL e) 100.1 mL The

asked by George on April 27, 2013
5. ### Chemistry

determine the approximate molarity of a solution of NaOH prepared by diluting 10ml of 6M NaOH to a volume of 400 ml. using the solution in the first part, 24.5ml of NaOH solution was required to neutralize 26.4ml of a .150M HCl

asked by Chuck on February 28, 2008
6. ### Chemistry (molarity) (sorta an emergency)

I'm doing a titration lab and writing a lab report where I'm sort of stuck on how exactly to find the concentration of HCl. These are the following info I have from the lab, Equation: HCl(aq)+NaOH(aq)-> H2O(l)+NaCl(aq) -Calculated

asked by Ray on November 13, 2016
7. ### acid-base titrations

For each of the following circumstances, indicate whether the calculated molarity of NaOH would be lower, higher or unaffected. Explain your answer in each case. a.the inside of the pipet used to transfer the standard HCI solution

asked by natash on April 21, 2008
8. ### chemistry

Could someone help me with this please? In chemistry, we did a lab in which he put brands of commerical vinegar in a microplate. We put in 10 drops of each vinegar in each plate thinger then we added 1 drop of phenolphthalein and

asked by Jeffrey on May 14, 2007
9. ### General Chemistry

Starting out with 50 mL of 0.20 M NaHCO3, calculate how many mL of 0.50 M NaOH solution to add to make 100 mL of approximately 0.10 M (total) buffer solution with a pH of 10.35. By adding NaOH, some of the NaHCO3 gets converted to

asked by Lucy on April 3, 2012
10. ### Chemistry

suppose you added 26.0 ml of 0.01 M NaOH to the solution, what is the molarity of excess NaOH in the mixture? what is the ph of this solution?

asked by Mollie on November 19, 2014

More Similar Questions