# chemistry

whats the pH if 25.0 ml of 2.0 M NaOH is added to 1.00 L of pure water?

1. 👍 0
2. 👎 0
3. 👁 193
1. First calculate the molarity of the NaOH. It is diluted 25 mL to 1,025 mL. So 2.0 M x (25/1025) = ??
NaOH is a strong electrolyte and is ionized 100%; therefore, OH^- = the molarity. Take it from here with the following:
pOH = - log (OH^-)
pH + pOH = 14.

1. 👍 0
2. 👎 0
2. Pure water is added to 25.0 mL of a 1.00 M HCL solution. The new solution has a volume of 2.00 L. What is the pH of the new solution.

1. 👍 0
2. 👎 0

## Similar Questions

1. ### Chemistry

1.What is the pH of a solution containing 0.042 M NaH2PO4 and 0.058 M Na2HPO4 ? The pKa of sodium phosphate is 6.86. pH = 6.86 + log [0.058] / [0.042]; pH = 6.86 + 0.14; pH = 7.00 That is my answer to the above question. The

2. ### chemistry

A volume of 100mL of 1.00 M HCl solution is titrated with 1.00 M NaOH solution. You added the following quantities of 1.00 M NaOH to the reaction flask. Classify the following conditions based on whether they are before the

3. ### Org. Chem.

what is the precipitate formed when HCl is added? I believe the answer is NaCl, but I am not sure and this precipitate only formed in the first NaOH extract, as precipitate was essentially nonexistent in the 2nd extract? Below is

4. ### chemistry

What volume of WATER MUST BE ADDED to 10.0 mL of 6.0 M NaOH to make a solution that is 0.30 M in NaOH? Assume that the volumes are additive. a. 10 mL b. 190 mL c. 200 mL d. 210 mL e. 500 mL

1. ### Science

The titration of 25.00ml of 0.1000m hypochlorous acid (3.5x10^-8) with 0.1500m NaOH. (a). What is the pH before any acid is added (b). What is the PH when 25.00ml of NaOH has been added?

2. ### chemistry

three student chemists measured 50.0 mL of 1.00 M NaOH in separate Styrofoam "coffee cup" calorimeters ( Part B). Brett added 50.0 mL of 1.10 M HCI to his solution of NaOH; Dale added 45.5 mL of 1.10 m HCL 9 eqaul moles) to his

3. ### Chemistry

1.0L of aqueous solution in which [H2CO3]=[HCO3^-]=0.10M and has [H^+]=4.2E-7. What is the concentration of [H^+] ofter 0.005 mole of NaOH has been added? H2CO3 ==> H^+ + HCO3^- k1 = (H^+)(HCO3^-)/(H2CO3) I don't know if you are

4. ### Chemistry

what volume of water must be added to 10ml og 6.0M NaOH to make a solution that is .30 M in NaOH How do I solve for this

1. ### Chemistry

Calculate the molarity of the H2SO4 solution if 17.45 mL of NaOH was necessary to reach the endpoint of titration. The molarity of the NaOH solution was 0.425 M and 26.30 mL of H2SO4 was added to the Erlenmeyer flask. H2SO4(aq) +

2. ### acid-base titrations

For each of the following circumstances, indicate whether the calculated molarity of NaOH would be lower, higher or unaffected. Explain your answer in each case. a.the inside of the pipet used to transfer the standard HCI solution

3. ### Chemistry

20.00 mL of 0.160 M HC2H3O2 (Ka=1.8x10^-5) is titrated with 0.200 M NaOH. Use the calculation to determine the: a) pH of the solution before the titration begins? (2) b) pH after 8.00 mL of NaOH has been added? (2) c) pH at the

4. ### chemistry

calculate the mass of NaOH neded to prepare 500mL of a 0.10 M solution. I'm pretty sure the answer is 2g, but how do I get to that? Another question: calculate the molar amount of KHP used to neutralize the NaOH solution. .51 g of