Chemistry

A 50-mL Mohr buret is connected to a 1-ft length of capillary tubing. The buret is then filled with water and the volume of water versus time is monitored as the water gradually flows through the capillary tubing.

This process is found to be first-order with a rate constant of 0.014 mL/sec. What will happen if the length of the capillary tube is doubled?

a)The process will still be first-order, but the rate constant will decrease.

b)The order and rate constant for the process will both change.

c)The order of the process will change, but the rate constant will be constant.

d)The process will still be first-order, but the rate constant will increase.

  1. 👍
  2. 👎
  3. 👁
  1. I know the answer's not C for sure
    and if there's a choice E then it's not that either

    1. 👍
    2. 👎
  2. It will still be first order but the constant will decrease.

    1. 👍
    2. 👎

Respond to this Question

First Name

Your Response

Similar Questions

  1. Chemistry

    The bubble in the tip of the buret is not removed prior to performing the NaOH standardization. Will the reported concentration of the NaOH be greater than, less than, or equal to the true concentration of the NaOH if the bubble

  2. Chemistry

    A student failed to notice an air bubble trapped in the tip of the buret during their experiment. What effect does this have on the calculated molarity of the NaOH solution?

  3. acid-base titrations

    For each of the following circumstances, indicate whether the calculated molarity of NaOH would be lower, higher or unaffected. Explain your answer in each case. a.the inside of the pipet used to transfer the standard HCI solution

  4. Chemistry

    A titration setup was used to determine the unknown molar concentration of a solution of NaOH. A .025 M HCl solution was used as the titration standard. The following data were collected. Trial 1 Trial 2 Trial 3 Initial NaOH Buret

  1. Chemistry

    This is a lab called Enthalpy and Entropy of Borax Dissolution and I just can't seem to get the right answers... Please help me fill in the blanks The _____ (acid/HCl?)is placed in the buret and the ____ (base/borax?) is placed in

  2. Chem 151

    Would my calculated molarity of HOAc in vinegar be too high, low, or unchanged if a) i forgot to rinse wet buret with vinegar b)delivered vinegar into a wet flask c)used a buret with a broken tip Any help please!!!

  3. Biology

    Your lab group is experimenting with the diffusion of molecules across a membrane. Dialysis tubing is used as a model cell membrane because is it semi-permeable, allowing small molecules to cross the membrane, but NOT larger

  4. CHEMISTRY PLEASE HELP

    Using the data collected for part b on your data sheet, calculate the molar mass of the unknown acid. Include the calculation for each trial and the average. Trial One Results: Mass unknown acid: 0.500g Final buret reading:

  1. APChem

    If an air bubble passes unnoticed through the tip of a buret during a titration (where a weak nonvolatile acid HA is the analyte) , the calculated molar mass of HA would be too high, too low, or not affected? I thought it would be

  2. science

    Does adding boiled, deionized water to the titrating flask to wash the wall of the erlenmeyer flask and the buret tip increase, decrease, or have no effect on the Ksp value of the Ca(OH)2?

  3. Chemistry

    A student titrated 1.852 g of a mixture containing potassium hydrogen phthalate, KHP....? A student titrated 1.852 g of a mixture containing potassium hydrogen phthalate, KHP, with 0.163 M NaOH solution. She recorded an initial

  4. CHEMISTRY

    If you use a dirty buret, the titrant leaves drops of solution behind as the meniscus descends during delivery of the solution. The volume actually delivered by the buret will be __________ the volume your readings of the buret

You can view more similar questions or ask a new question.