chemistry

what is the ratio of water drops to EDTA if 2 drops of EDTA was needed to change the color of 20 drops of water with unknown hardness?

a. 10
b. 5
c. 0.1
d. 1.0

please explain..

  1. 👍
  2. 👎
  3. 👁
  1. Let's see. Bob Pursley did one early this AM that was 3 drops to 20 drops, so 3:20 (6.7) was the answer. Wouldn't this be done the same way?

    1. 👍
    2. 👎
  2. so would the answer be a. 10??

    1. 👍
    2. 👎
  3. That looks right to me.
    H2O/EDTA = 20/3 = 6.7

    H2O/EDTA = 20/2 = 10

    1. 👍
    2. 👎

Respond to this Question

First Name

Your Response

Similar Questions

  1. Chemistry

    IN my experiment, I was doing a qualitative analysis of Group I and II anions using a flowchart. IN the chart I added 5 drops of 0.1M AgNO3 and several drops of 3M HNO3 to 5 drops of solution and found that a precipitate was

  2. Analytical chemistry

    A 25.0-mL solution of 0.0660 M EDTA was added to a 33.0-mL sample containing an unknown concentration of V3 . All V3 present formed a complex, leaving excess EDTA in solution. This solution was back-titrated with a 0.0450 M Ga3

  3. chemistry

    A 50.00-mL sample of groundwater is titrated with 0.0900 M EDTA. Assume that Ca2 accounts for all of the hardness in the groundwater. If 11.40 mL of EDTA is required to titrate the 50.00-mL sample, what is the hardness of the

  4. Chemistry (Re-post)

    A solution contains 1.694 mg of CoSO4 (MW 155.0) per mL. Calculate a) The volume of 0.008640 M EDTA needed to titrate a 25.00 ml aliquot of this solution. So this is my working out for this section, Step 1. Moles of CoSO4 =

  1. Chem 2

    A 100-mL sample of water is titrated with EDTA solutions in problem 2. The same amount of Mg2+ is added as previously, and the volume of EDTA required is 31.84mL. What volume of EDTA is used in titrating the Ca2+ in hard water?

  2. Chemistry

    A 1.0 mL volume of 0.010 M H2SO4 is added to a mixture of 6 drops of 0.010 M HIO3, 14 drops of deionized water, and 1 drop of starch solution. A color change in the reaction mixture occurred after 56 seconds. a. Assuming 20 drops

  3. chemistry

    25.00 mL aliquots of the solution from Part 1 are titrated with EDTA to the Eriochrome Black T end point. A blank containing a small measured amount of Mg2+ requires 2.60 mL of the EDTA to reach the end point. An aliquot to which

  4. Analytical Chem

    The following electrochemical cell can be used to calculate the formation constant Kf for a metal and EDTA. The cell has a voltage of -0.262V. The right half cell contains a metal (M^2+) with a standard reduction potential of

  1. Chemistry

    A solution contains 1.694 mg of CoSO4 (MW 155.0) per mL. Calculate a) The volume of 0.008640 M EDTA needed to titrate a 25.00 ml aliquot of this solution. Step 1. 0.001694g * 25ml * 1/155 g/mol= 0.0002732 mol Step 2. Volume of

  2. Chemistry

    Calculate the molarity of 3 drops (0.15mL) of a 0.5M Na3PO4 solution after adding 15 drops (.75mL) of water. (Presume drops are the same size, one drop = 0.05mL)((Presume volumes are additive)) So far I've figured .15g

  3. analytical chemistry

    An EDTA solution is standardized against a solution of primary standard CaCO3 (0.5622 g dissolve in 1000 ml of solution) and titrating aliquots of it with the EDTA. If a 25.00 ml aliquot required 21.88 ml of the EDTA, what is the

  4. chemistry

    The urine excreted by an adult patient over 24 hours was collected and diluted to give 2.000L sample. at ph 10 EDTA FORMS 1:1 COMPLEX WITH BOTH Mg2+ and Ca2+ and after buffering at this pH a 10mL aliquot of the sample required

You can view more similar questions or ask a new question.