chemistry

what is the ratio of water drops to EDTA if 2 drops of EDTA was needed to change the color of 20 drops of water with unknown hardness?

a. 10
b. 5
c. 0.1
d. 1.0

  1. 👍
  2. 👎
  3. 👁
  1. Bob Pursley answered below.

    1. 👍
    2. 👎
  2. Bob pursle answered a very similar question this one has 2 drops and unknown hardness...

    1. 👍
    2. 👎
  3. What is the Answer

    1. 👍
    2. 👎

Respond to this Question

First Name

Your Response

Similar Questions

  1. Chemistry

    IN my experiment, I was doing a qualitative analysis of Group I and II anions using a flowchart. IN the chart I added 5 drops of 0.1M AgNO3 and several drops of 3M HNO3 to 5 drops of solution and found that a precipitate was

  2. Analytical chemistry

    A 25.0-mL solution of 0.0660 M EDTA was added to a 33.0-mL sample containing an unknown concentration of V3 . All V3 present formed a complex, leaving excess EDTA in solution. This solution was back-titrated with a 0.0450 M Ga3

  3. chemistry

    A 50.00-mL sample of groundwater is titrated with 0.0900 M EDTA. Assume that Ca2 accounts for all of the hardness in the groundwater. If 11.40 mL of EDTA is required to titrate the 50.00-mL sample, what is the hardness of the

  4. Chemistry (Re-post)

    A solution contains 1.694 mg of CoSO4 (MW 155.0) per mL. Calculate a) The volume of 0.008640 M EDTA needed to titrate a 25.00 ml aliquot of this solution. So this is my working out for this section, Step 1. Moles of CoSO4 =

  1. Chem 2

    A 100-mL sample of water is titrated with EDTA solutions in problem 2. The same amount of Mg2+ is added as previously, and the volume of EDTA required is 31.84mL. What volume of EDTA is used in titrating the Ca2+ in hard water?

  2. Analytical Chem

    The following electrochemical cell can be used to calculate the formation constant Kf for a metal and EDTA. The cell has a voltage of -0.262V. The right half cell contains a metal (M^2+) with a standard reduction potential of

  3. chemistry

    The urine excreted by an adult patient over 24 hours was collected and diluted to give 2.000L sample. at ph 10 EDTA FORMS 1:1 COMPLEX WITH BOTH Mg2+ and Ca2+ and after buffering at this pH a 10mL aliquot of the sample required

  4. chemistry

    25.00 mL aliquots of the solution from Part 1 are titrated with EDTA to the Eriochrome Black T end point. A blank containing a small measured amount of Mg2+ requires 2.60 mL of the EDTA to reach the end point. An aliquot to which

  1. Chemistry

    A solution contains 1.694 mg of CoSO4 (MW 155.0) per mL. Calculate a) The volume of 0.008640 M EDTA needed to titrate a 25.00 ml aliquot of this solution. Step 1. 0.001694g * 25ml * 1/155 g/mol= 0.0002732 mol Step 2. Volume of

  2. analytical chemistry

    An EDTA solution is standardized against a solution of primary standard CaCO3 (0.5622 g dissolve in 1000 ml of solution) and titrating aliquots of it with the EDTA. If a 25.00 ml aliquot required 21.88 ml of the EDTA, what is the

  3. Chemistry

    Calculate the molarity of 3 drops (0.15mL) of a 0.5M Na3PO4 solution after adding 15 drops (.75mL) of water. (Presume drops are the same size, one drop = 0.05mL)((Presume volumes are additive)) So far I've figured .15g

  4. Chemistry

    A 1.0 mL volume of 0.010 M H2SO4 is added to a mixture of 6 drops of 0.010 M HIO3, 14 drops of deionized water, and 1 drop of starch solution. A color change in the reaction mixture occurred after 56 seconds. a. Assuming 20 drops

You can view more similar questions or ask a new question.