MATH

A collar of Styrofoam is made to insulate a pipe. Find its volume . The large R is to the outer rim. The small radius r is to the edge of the insulation. Use 3.14 for pi. r = 5 in. R = 6 in. h = 19 in. Round to two decimal places. It says to subtract volume of the inner cylinder from the volume of the outer cylinder. Round answer two decimal places.

  1. 👍
  2. 👎
  3. 👁
  1. volume = ( R^2 - r^2) pi h

    1. 👍
    2. 👎
  2. subscribe to callmecarson on yt

    1. 👍
    2. 👎
  3. 69

    1. 👍
    2. 👎

Respond to this Question

First Name

Your Response

Similar Questions

  1. math

    An open box is made from a rectangular piece of cardboard measuring 16 cm by 10cm. Four equal squares are to be cut from each corner and flaps folded up. Find the length of the side of the square which makes the volume of the box

  2. physics

    Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in figure below, the pressure is P1 = 1.75X104 Pa and the pipe diameter is 6.00 cm. At another point y = 0.250 m higher, the pressure is P2 =

  3. physics

    Styrofoam has a density of 300 kg/m^3. What is the maximum mass that can hang without sinking from a 50 cm diameter styrofoam sphere in water? (Assume the volume of the mass is negligible compared to that of the sphere.) V sphere

  4. Physics

    Please someone help..A horizontal pipe 10.0cm in diameter has a smooth reduction to a pipe 5.0cm in diameter. If the pressure of the water in the large pipe is 80000Pa and the pressure in the small pipe is 60000Pa at what rate

  1. Physics

    Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in the figure below, the pressure is 1.70 105 Pa and the pipe radius is 2.50 cm. At the higher point located at y = 2.50 m, the pressure is

  2. Physics

    Water is flowing in a pipe with a varying cross-section area, and at all points the water completely fills the pipe. At point 1 the cross-section area of the pipe is 0.080 m^2, and the magnitude of the fluid velocity is 2.50m/s.

  3. phys

    Water flows steadily from an open tank into a pipe as shown in the figure. The elevation of the top of the tank is 12.3 m, and the elevation at the pipe is 3.80 m. The initial cross-sectional area of the pipe (at point 2) is

  4. MATHS

    A CYLINDRICAL PIPE MADE OF METAL IS 3 CM THICK .IF THE INTERNAL RADIUS OF THE PIPE IS 10 CM, FIND THE VOLUME OF THE METAL USED IN MAKING 3M OF THE PIPE RADIUS OF INTERNAL PIPE =10CM RADIUS OF EXTERNAL PIPE =13CMVOLUME OF PIPE=PI

  1. Thermodynamics and Heat Transfer

    A steam pipe is 75 mm external diameter and is 80 m long. It conveys steam at a rate of 1000 kg/h at a pressure of 2 Mpa. The steam enters the pipe with a dryness fraction of 0.98 and is to leave the pipe with a dryness of not

  2. Mathematics

    A cylindrical pipe 28m long. Its internal radius is 3.5cm and external radius is 5cm. Calculate the volume in cm of metal used in making the pipe (2) the volume of water in metres that the pipe can hold.

  3. Physics 212

    Styrofoam has a density of 300kg/m3. What is the maximum mass that can hang without sinking from a 40.0cm -diameter Styrofoam sphere in water? Please help!

  4. Physics

    Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in the figure below, the pressure is 1.85 105 Pa and the pipe radius is 2.80 cm. At the higher point located at y = 2.50 m, the pressure is

You can view more similar questions or ask a new question.