Science

What is the effect on molarity for NaOH when balance used to weigh KHP is not properly calibrated and always reads 0.15 g too low.

  1. 👍 0
  2. 👎 0
  3. 👁 49

Respond to this Question

First Name

Your Response

Similar Questions

  1. chemistry

    The KHP used in the titration with NaOH was contaminated with sodium hydrogen phyhalate (NaHC8H4O4), but you didn't know it. State the effect of the final result (falsely high, falsely low, or unaffected) Explain. thanks These

    asked by bria on September 20, 2006
  2. Chem Question

    What is the molarity of a NCL solution if 37.50 mL of the acid is needed to neutralize 25.00 mL of 0.0725 M NaOH? I'm not quite sure how to go about doing this one. And also this one thing. The following technical errors were

    asked by Angie on March 8, 2007
  3. Chemistry (molarity)

    What would the effect on your molarity of NaOH be if you had added 35 mL of water to dissolve the KHP (acid) instead of 25 mL? Explain. My answer so far is that adding more water shouldn't affect the molarity at all because water

    asked by Ray on November 10, 2016
  4. chemistry

    KHP is a monoprotic acid with a molar mass of 204.22 g/mol. The titration data are as following. The average concentration of NaOH solution is M. 1 2 3 mass of KHP (g) 2.789 2.543 2.612 vol NaOH used (mL) 27.77 23.22 27.12 You

    asked by jared on May 16, 2007
  5. chemistry

    HCL is tritrated with NaOH. KHP is then added. A possible source of systematic error in this experiment is failure to dry the KHP. If this occured, would the final wt% NA2CO3 be falsely high, falsely low, or unaffected. Give

    asked by bria on September 6, 2006
  6. Chemistry

    Calculate the theoretical amount of .5M NaOH that it would take to neutralize approx. 2.0 g KHP. KHP is a monoprotic acid, the molar mass of KHP is 204.22 g/mol and the molar mass of NaOH is 40.00 g/mol. Answer in terms of mL. I

    asked by Brad on March 28, 2016
  7. science-chemistry

    We performed a titration with NaOH solution with KHP. Now I need to calculate the average molarity of NaOH based on this data Weight of khp= 0.1083 g Volume of naoh = 6.4 ml Then if i get this how do i get the molarity of ch3cooh

    asked by cassy on April 23, 2014
  8. chemistry

    how do i calculate the NaOH molarity from a titration of KHP and NaOH after preparing KHP to standardise NaOH. KHP mass was 2.0378g dissoveld in distilled water to fill up a 100ml volumetric flask and only 10ml of this solution

    asked by k on March 22, 2013
  9. Chemistry

    Given the following equation and information answer the following questions, KHC8H4O4 (aq) + NaOH(aq) > KNaC8H4O4 (aq) + H2O(l) 3. What is the molarity of a NaOH solution if 26.50 mL of it is required to neutralize 0.4150 g of

    asked by Yassine on March 10, 2018
  10. Chem.

    To standardize a solution of NaOH, one uses a primary standard called potassium hydrogen phthalate (KHP). It is a monoprotic acid. It has a molar mass of 204.33g/mol. Suppose you weigh out .556g of KHP and dissolve it in water. It

    asked by Anonymous! on March 17, 2014

More Similar Questions