Chem

Using the Absorbance (0.455) of your Unknown SCN- solution and the slope (3163.9) from your Calibration Curve, calculate the concentration of SCN- in the solution created from 5.0 mL 0.200 M Fe(NO3)3, 40.0 mL H2O and 5.0 mL SCN-. How would I calculate?

  1. 👍 0
  2. 👎 0
  3. 👁 236
  1. A = ebc where e is the molar absorptivity = slope of the line.

    0.455 = 3163.9*c
    Calculate c.

    1. 👍 0
    2. 👎 0

Respond to this Question

First Name

Your Response

Similar Questions

  1. chemistry

    When the glucose solution described in part A is connected to an unknown solution via a semipermeable membrane, the unknown solution level rises. Based on this information, what can be said about these two solutions? a.) The

    asked by david on February 24, 2010
  2. chemistry

    The standard solution of FeSCN2+ (prepared by combining 9.00 mL of 0.200 M Fe(NO3)3 w/1.00 mL of 0.0020 M KSCN) has an absorbance of 0.520. If a trial's absorbance is measured to be 0.275 and its initial concentration of SCN–

    asked by Amy on April 8, 2008
  3. chem

    An unknown was prepared with the concentration of 0.000630 M. A Beer's Law plot was prepared using the absorbance values from standard solutions of ASA and a line drawn through all the points passed through the origin with a slope

    asked by eve on April 20, 2009
  4. chem

    An unknown was prepared with the concentration of 0.000630 M. A Beer's Law plot was prepared using the absorbance values from standard solutions of ASA and a line drawn through all the points passed through the origin with a slope

    asked by eve on April 19, 2009
  5. Chemistry

    If all of the SCN- was not converted completely converted to FeNCS^2+ when the calibration curve was prepared, would this raise or lower the value of Keq? Explain

    asked by Lyndsay on March 22, 2016
  1. science

    college chemistry-absorbance of an equilibrium mixture Problem: A student mixed 4.00mL of 1.02x10^(-1) M Fe(NO3)3 with 100.00mL of 1.98*10^(-4) M KSCN, using 5.0*10^(-1) M HNO3 as the solvent for both solutions, and found the

    asked by Mary on March 14, 2009
  2. chemistry

    The standard solution of FeSCN2+ (prepared by combining 9.00 mL of 0.200 M Fe(NO3)3 w/1.00 mL of 0.0020 M KSCN) has an absorbance of 0.520. If a trial's absorbance is measured to be 0.275 and its initial concentration of SCN–

    asked by david on April 14, 2008
  3. chemistry

    The standard solution of FeSCN2+ (prepared by combining 9.00 mL of 0.200 M Fe(NO3)3 w/1.00 mL of 0.0020 M KSCN) has an absorbance of 0.510. If a trial's absorbance is measured to be 0.250 and its initial concentration of SCN–

    asked by Jason on April 9, 2008
  4. Chem

    Calibration data for a bromide ion-selective electrode (ISE) was collected and recorded below. The potential of the ISE was measured against a saturated calomel electrode (SCE). All solutions were buffered at a pH of 7.56. A

    asked by Cassie on March 30, 2015
  5. Chemistry DrBob

    You told me the steps on a previous post but i must have forgot how to work out absorbance or ICE cus i keep getting the wrong answer ... The standard solution of FeSCN2+ (prepared by combining 9.00 mL of 0.200 M Fe(NO3)3 w/1.00

    asked by Amy on April 10, 2008

You can view more similar questions or ask a new question.