FLUID MECHANICS

Air at 45°C is flowing steadily in a 25 cm-diameter horizontal pipe made of plastic at
a rate of 900 l/min. Determine the head loss, and the required pumping power
input for flow over a 175m-long section of the pipe.

  1. 👍 0
  2. 👎 0
  3. 👁 45
asked by ANNA

Respond to this Question

First Name

Your Response

Similar Questions

  1. physics

    A horizontal pipe of diameter 0.845 m has a smooth constriction to a section of diameter 0.507 m. The density of oil flowing in the pipe is 821 kg/m3 . If the pressure in the pipe is 8350 N/m2 and in the constricted section is

    asked by ryan on June 17, 2011
  2. physics

    Water is flowing into a factory in a horizontal pipe with a radius of 0.0223 m at ground level. This pipe is then connected to another horizontal pipe with a radius of 0.0400 m on a floor of the factory that is 10.6 m higher. The

    asked by reuben on June 23, 2014
  3. physic

    you need to extend a 2.50 inch diameter pipe, but you only have 1.00 inch diameter pipe on hand.you make a fitting to connect these pipes end to end. if the water is flowing at 6.00cm/s in the wide pipe, how fast will it be

    asked by steve on July 20, 2010
  4. Physics

    What is the pressure change in methyl alcohol (SG =0.791) flowing from 4.0 cm diameter pipe to a 1.5 cm diameter pipe if the velocity in the larger pipe is 0.40 m/s?

    asked by Justin on April 23, 2019
  5. Physics

    A liquid of density 1.23 × 103 kg/m3 flows steadily through a pipe of varying diameter and height. At location 1 along the pipe the flow speed is 9.23 m/s and the pipe diameter is 1.07 × 101 cm. At location 2 the pipe diameter

    asked by Ashley on November 14, 2013
  6. Physics

    Water (η = 1.00E-3 Pa*s) is flowing through a horizontal pipe with a volume flow rate of 0.0120 m3/s. As the figure below shows, there are two vertical tubes that project from the pipe. Assume that H = 0.0421 m and L = 0.706 m.

    asked by Alexa on November 14, 2012
  7. Physics

    A horizontal pipe contains water at a pressure of 120kPa flowing with a speed of 1.4m/s . The pipe narrows to one-half its original diameter. a) what is the speed of the water? b) what is the pressure of the water? I tried using

    asked by Lhaedy on December 11, 2013
  8. physics

    Water is flowing through a horizontal pipe of varying cross section. At section 1,the diameter is 12cm at a pressure of 80000 Pa. At section 2, the pipe has a diameter of 6cm and the pressure is 60000 Pa. Find the speed of water

    asked by Haiano on June 9, 2014
  9. Fluid Mechanics

    Water flows into a cylindrical tank through pipe 1 at a rate of 25 ft/s and leaves through pipe 2 at 10 ft/s and through pipe 3 at 12 ft/s. Pipe 4 is an open air vent. Internal diameters of the pipes are: D1=3 in, D2= 2 in, D3=2.5

    asked by Katy on September 10, 2013
  10. physics

    1.) water is flowing through a horizontal pipe of varying crosection, the diameter is 12.0 cm at a pressure of 8.0x10^4 Pa. at section 2, the pipe has a diameter of 6.0 cm and the pressure is 6.0x10^4 Pa. find the speed of water

    asked by erjee on September 5, 2013

More Similar Questions