# mechanical properties of materials

posted by .

following data was obtained from a tensile test of steel. The test specimen was 15mm in diameter and 50 mm in length
5 /0.005
10 /0.015
30 /0.048
50 /0.084
60 /0.102
64.5 /0.109
67/ 0.119
68 /0.137
69/ 0.160
70 /0.229
72 /0.300
76 /0.424
84 /0.668
92 /0.965
100 /1.288
112 /2.814
127 /fracture

(a) Using the data,plot a stress-strain curve, marking the proportional limit and calculate the ultimate strength
(b) Given that , at fracture , the minimum diameter was 9.5 mm, calculate the reduction in cross-sectional area, expressing the answer as a percentage of the original cross-sectional area.

## Similar Questions

1. ### Mechanics

A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. Using the data listed in the table, plot the stressâ€“strain diagram, and determine approximately the modulus of toughness. …
2. ### mechanical properties of materials

following data was obtained from a tensile test of steel. The test specimen was 15mm in diameter and 50 mm in length Load (kN) Elongation(mm) 5 0.005 10 0.015 30 o.048 50 0.084 60 0.102 64.5 0.109 67 0.119 68 0.137 69 0.160 70 0.229 …
3. ### mechanical properties of materials

A cylindrical steel bar is required to support a load of 650 N. the required bar must be 0.17 m in length and must not deform by more than 0.015 mm. given that the Young's modulus of steel is 210 GPa, calculate the minumum diameter …
4. ### mechanical properties of materials

A cylindrical steel bar is required to support a load of 650 N. the required bar must be 0.17 m in length and must not deform by more than 0.015 mm. given that the Young's modulus of steel is 210 GPa, calculate the minumum diameter …
5. ### mechanical properties of materials

following data was obtained from a tensile test of steel. The test specimen was 15mm in diameter and 50 mm in length Load (kN) /Elongation(mm) 5 /0.005 10 /0.015 30 /0.048 50 /0.084 60 /0.102 64.5 /0.109 67/ 0.119 68 /0.137 69/ 0.160 …
6. ### mechanics of materials

The following data was obtained from a tensile test of steel. The test specimen was 15mm in diameter and 50 mm in length. Load(kN)/elongation mm) 5 /0.005 10 /0.015 30 /0.048 50 /0.084 60 /0.102 64.5 /0.109 67 /0.119 68 /0.137 69 /0.16 …
7. ### mechanics of materials

The following data was obtained from a tensile test of steel. The test specimen was 15mm in diameter and 50 mm in length. Load(kN)/elongation mm) 5 /0.005 10 /0.015 30 /0.048 50 /0.084 60 /0.102 64.5 /0.109 67 /0.119 68 /0.137 69 /0.16 …
8. ### mechanical properties of materials

A flat plate specimen of a soft metal alloy is to be tested by pulling on round pins inserted through the ends of the plate, as illustrated below (a) Calculate the required diameter of the pins, given that the plate is 8.0 mm thick, …
9. ### engineering

A steel tube 30 mm outside diameter and 25 mm internal diameter and length 500 mm is subjected to a tensile load of 37 KN, determine the change in length in mm to 3 decimal places when the load was applied. For the material E = 210 …
10. ### Material mechanics

following data was obtained from a tensile test of steel. The test specimen was 15mm in diameter and 50 mm in length Load (kN) Elongation(mm) 5 0.005 10 0.015 30 o.048 50 0.084 60 0.102 64.5 0.109 67 0.119 68 0.137 69 0.160 70 0.229 …

More Similar Questions