Please help me !!! for solution of this question Water enters a horizontal pipe with a rectangular cross section at a speed of 1.00 m/s. The width of the pipe remains constant but the height decreases. 27.3 m from the

88,700 results
  1. AP Physics - Fluids

    A 6.0-cm diameter horizontal pipe gradually narrows to 4.0 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 32 kPa and 24 kPa, respectively. What is the volume rate of flow? I know to use Bernoulli's

  2. Physic

    1. Water at a pressure of 3.00 x 10 5th Pa flows through a horizontal pipe at a speed of 1.00 m/s. The pipe narrows to one-fourth its original diameter. What is the speed of the flow in the narrow section? Not sure was successfully posted

  3. Physics

    Please someone help..A horizontal pipe 10.0cm in diameter has a smooth reduction to a pipe 5.0cm in diameter. If the pressure of the water in the large pipe is 80000Pa and the pressure in the small pipe is 60000Pa at what rate does water flow through the

  4. physics, buoyance

    Water flows at a rate of 25L/min through a horizontal 8.0-cm-diameter pipe under a pressure of 5.7Pa . At one point, calcium deposits reduce the cross-sectional area of the pipe to 40cm2 . Part A What is the pressure at this point? (Consider the water to

  5. Physics--Pressure

    a house at the bottom of a hill is fed by a full tank of water 5m deep and connected to the house by a pipe that is 110m long at an angle of 58 from the horizontal. a) determine the water gauge pressure at the house b) how high could the water shoot if it

  6. Physics

    For an ideal fluid flowing through a horizontal pipe, Bernoulli's principle and the continuity equation state that the pressure within the pipe does which of the following? Pressure descreased pipe diameter increase?

  7. Physics

    Water is flowing in a pipe with a varying cross-section area, and at all points the water completely fills the pipe. At point 1 the cross-section area of the pipe is 0.080 m^2, and the magnitude of the fluid velocity is 2.50m/s. Calculate the volume of the

  8. Physics

    Water flows at 12 m/s in a horizontal pipe with a pressure of 3.0 x 10 4 N/m2 . If the pipe widens to twice its original radius, what is the pressure in the wider section?

  9. general physics

    Determine the minimum gauge pressure needed in the water pipe leading into a building if water is to come out of a faucet on the twelfth floor, 38 m above that pipe.

  10. physics

    A horizontal pipe has a cross sectional area of 40.0 cm^2 at the wider portions and 10.0 cm^2 at the constriction. Water is flowing in the pipe, and the discharge from the pipe is 6.00*10^-3 m^3/s(6.00 L/s). Find (a) the flow speeds at the wide and the

  11. math

    A plumber has a very long piece of pipe that is used to run city water parallel to a major roadway. The pipe is cut into two sections. One section of pipe is 12 ft. shorter than the other. If ¾ of the length of the shorter pipe is 120 ft., How long is the

  12. phys

    Water flows steadily from an open tank into a pipe as shown in the figure. The elevation of the top of the tank is 12.3 m, and the elevation at the pipe is 3.80 m. The initial cross-sectional area of the pipe (at point 2) is 5.60×10−2 m^2; and at where

  13. physics

    Water flows steadily from an open tank into a pipe. The elevation of the top of the tank is 10.2 m, and the elevation at the pipe is 3.90 m. The initial cross-sectional area of the pipe is 6.40×10^−2 m; and at where the water is discharged from the

  14. Physics

    A horizontal pipe, 10 cm in diameter, has a smooth reduction to a pipe 5 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, what is the flow speed of the water (in m/s) in the

  15. Physics

    The water flowing through a 1.9 cm (inside diameter) pipe flows out through three 1.3 cm pipes. (a) If the flow rates in the three smaller pipes are 24, 18, and 13 L/min, what is the flow rate in the 1.9 cm pipe? (b) What is the ratio of the speed of water

  16. Fluid Mechanics

    Water flows into a cylindrical tank through pipe 1 at a rate of 25 ft/s and leaves through pipe 2 at 10 ft/s and through pipe 3 at 12 ft/s. Pipe 4 is an open air vent. Internal diameters of the pipes are: D1=3 in, D2= 2 in, D3=2.5 in, D4=2 in. Calculate a)

  17. Math - Calculus

    Water is flowing in a cylindrical pipe of radius 1 inch. Because water is viscous and sticks to the pipe, the rate of flow varies with distance from the center. The speed of the water at distance r inches from the center is 10(1-(r^2)) per second. What is

  18. physics

    Practice Problem 13.9 Let's begin by looking at a flow problem in which the diameter of a pipe changes along the flow path. We will need to use both the continuity equation and Bernoulli's equation for this problem. Water enters a house through a pipe with

  19. Physics

    A horizontal water pipe goes from a large diameter to a small diameter and then back to the first diameter as shown in the figure below. The level of water (8cm in the larger tube and 4 cm in the constricted tube) in the small vertical tubes provides us

  20. Physics

    A horizontal pipe narrows from radius of 0.250 m to 0.100m.If the speed of the water in the pipe is 1.00m/s in the larger radius pipe,what is the speed in the smaller pipe

  21. Physics

    Water flows into one end of a horizontal, cylindrical pipe at 2.0 m/s. The pipe then narrows until its diameter at the opposite end is only 1/3 of that at the beginning. (a) What is the flow speed at the narrow end of the pipe? (b) What is the pressure

  22. physics

    A house at the bottom of a hill is fed by a full tank of water 5.0 m deep and connected to the house by a pipe that is 110 m long at an angle of 58° from the horizontal (Fig. 13–48). (a) Determine the water gauge pressure at the house. (b) How high

  23. physics

    Water discharges from a horizontal, cylindrical pipe at the rate of 5.00x10^-3 m^3/s. At a point in the pipe where the cross-section is 1.000x10^-3 m^2, the absolute pressure is 1.60x10^5 Pa. What is the pipe radius at a constriction if the pressure there

  24. computers

    1. Water at a pressure of 3.00 x 10 5th Pa flows through a horizontal pipe at a speed of 1.00 m/s. The pipe narrows to one-fourth its original diameter. What is the speed of the flow in the narrow section?

  25. Math

    When an engineer inspects a pipeline she notices a high water mark. How much space is there between the high water level and the top of the pipe, to the nearest hundredth. The diameter of the pipe is 1.2m and the horiztonal distance across the surface of

  26. Physics

    Water flows under pressure from one pipe into a second pipe having half the diameter. The volume flow rate in the narrow pipe is ________ that in the wide pipe, and the speed of the water in the narrow pipe is _______ that in the wide pipe

  27. Thermodynamics and Heat Transfer

    A steam pipe is 75 mm external diameter and is 80 m long. It conveys steam at a rate of 1000 kg/h at a pressure of 2 Mpa. The steam enters the pipe with a dryness fraction of 0.98 and is to leave the pipe with a dryness of not less than 0.96. The pipe must

  28. College Physics

    A horizontal pipe has a cross sectional area of 40.0 cm^2 at the wider portions and 10.0 cm^2 at the constriction. Water is flowing in the pipe, and the discharge from the pipe is 6.00*10^-3 m^3/s(6.00 L/s). Find (a) the flow speeds at the wide and the

  29. physics

    a drinking fountain projects water at an initial angle of 50 degrees above the horizontal and the water reaches a maximum height of 0.150 m above the point of exit. assume air resistance is negligible. calculate the speed at which the water leaves the

  30. physics

    1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm? The pressure at the larger end of the pipe is

  31. Science

    Hi Just want to know if water from a 20mm Polyethylene pipe under pressure of 3 bars passes to a 25mm polyethylene will cause a slight increase in volume output with a little drop in pressure? If yes then to obtain this benefit , up to whay size can we go

  32. math

    a 15 foot long standard weight pipe with a diameter of 4 inches is filled with water. what would be the total approximate weight of the pipe and the water it contains? If I recall my non-metric units, 1 cubic foot of water weighs about 62.4 pounds. the

  33. Physics

    A horizontal pipe 10cm has asmootion to apipe 5 cm in diameter if the pressure of water in the large pipe is 80000pa and the pressure in the smaller pipe is 60000pa at what rate does water flow through the pipes

  34. physics

    A horizontal pipe 17.00 cm in diameter has a smooth reduction to a pipe 8.50 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?

  35. physics

    Water flows at 0.58 m/s through a pipe 11 cm in diameter when the pressure is 450,000 Pa. Determine the water velocity & the pressure in the pipe if it shrinks down to 5 cm in diameter. You can assume that the pipe is horizontal & ρwater = 1000 kg/m3.

  36. Physics

    I was walking through my local home supply store the other day carrying a 10 ft length of plastic pipe. The pipe was horizontal and my hand was supporting the middle of the pipe. I noticed that when I took two steps each second the ends of the pipe would

  37. Physics -- sound

    An organ pipe that is closed at one end has a fundamental frequency of 146 Hz. There is a leak in the church roof, and some water gets into the bottom of the pipe, as shown in the Figure. The organist then finds that this organ pipe has a frequency of 273

  38. physics

    A 5.4 cm diameter horizontal pipe gradually narrows to 3.7 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 35.0 kPa and 21.0 kPa, respectively. What is the volume rate of flow?

  39. physics

    Water is pumped at a rate of 24 cubic meter per second through a 0.50 cm radius pipe on the main floor of the house to a 0.35 cm radius pipe on the solar hot water collector 4.0 m higher on the roof. If the pressure in the pipe on the roof is 120000 Newton

  40. physics

    Water is flowing at 3 m/s in a circular pipe. If the diameter of the pipe decreases to four-ninth its former value, what is the velocity of the water downstream? Answer in units of m/s.

  41. Basic Physics

    Determine the minimum gauge pressure needed in the water pipe leading into a building if water is to come out of a faucet on the twelfth floor, 41m above that pipe.

  42. physics

    Please help me !!! for solution of this question Water enters a horizontal pipe with a rectangular cross section at a speed of 1.00 m/s. The width of the pipe remains constant but the height decreases. 27.3 m from the entrance, the height is half of what

  43. physics

    water moving in a horizontal pipe has a velocity of 9 m/s when the radius of the pipe os 0.025m. Determine the velocity of the water when it enters a wider section of the pipe and the radius is 0.075m.

  44. physics

    Water enters a horizontal pipe with a rectangular cross section at a speed of 1.00 m/s. The width of the pipe remains constant but the height decreases. 27.3 m from the entrance, the height is half of what it is at the entrance. If the water pressure at

  45. Physic

    Water enters a horizontal pipe with a rectangular cross section at a speed of 1.00 m/s. The width of the pipe remains constant but the height decreases. 27.3 m from the entrance, the height is half of what it is at the entrance. If the water pressure at

  46. physics

    Water is flowing into a factory in a horizontal pipe with a radius of 0.0223 m at ground level. This pipe is then connected to another horizontal pipe with a radius of 0.0400 m on a floor of the factory that is 10.6 m higher. The connection is made with a

  47. PHYSICS

    Water flowing out of a horizontal pipe emerges through a nozzle. The radius of the pipe is 1.5 cm, and the radius of the nozzle is 0.42 cm. The speed of the water in the pipe is 0.68 m/s. Treat the water as an ideal fluid, and determine the absolute

  48. Physics

    Water (η = 1.00E-3 Pa*s) is flowing through a horizontal pipe with a volume flow rate of 0.0120 m3/s. As the figure below shows, there are two vertical tubes that project from the pipe. Assume that H = 0.0421 m and L = 0.706 m. Calculate the radius of the

  49. physics

    Water flows in a cylindrical, horizontal pipe. As the pipe widens to twice its initial diameter the pressure in the pipe changes. Calculate the change in pressure between the wide and narrow regions of the pipe. Give your answer as an expression in terms

  50. physics

    A horizontal pipe (Venturi Tube) 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 2.0 x 105 Pa and the pressure in the smaller pipe is 5.0 x 104 Pa, at what rate does water flow

  51. physics

    A horizontal pipe (Venturi Tube) 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.0 x 105 Pa and the pressure in the smaller pipe is 3.0 x 104 Pa, at what rate does water flow

  52. physics

    A large water tank has an inlet pipe and an outlet pipe. The inlet pipe has a diameter of 2.19 cm and is 1.25 m above the bottom of the tank. The outlet pipe has a diameter of 5.93 cm and is 4.85 m above the bottom of the tank. A volume of 0.411 m^3 of

  53. physics

    A horizontal pipe 17.00 cm in diameter has a smooth reduction to a pipe 8.50 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?

  54. physic

    Water flows through a 4.0-cm-diameler horizontal pipe ata speed uf 1.3 m/s. The pipe then narrows down to a diameter of 2.0 cm. Ignoring viscosity, what is the pressure difference between the wide and narrow sections of the pipe

  55. physics

    In the figure below, the fresh water behind a reservoir dam has depth D = 13 m. A horizontal pipe 6.0 cm in diameter passes through the dam at depth d = 6.0 m. A plug secures the pipe opening. (a) Find the magnitude of the frictional force between plug and

  56. Physics

    A large water tank has an inlet pipe and an outlet pipe. The inlet pipe has a diameter of 2.19 cm and is 2.13 m above the bottom of the tank. The outlet pipe has a diameter of 5.49 cm and is 4.85 m above the bottom of the tank. A volume of 0.359 m3 of

  57. physics

    Water flows through a 4.0-cm-diameter horizontal pipe at a speed of 1.3m/s . The pipe then narrows down to a diameter of 2.0cm . Ignoring viscosity, what is the pressure difference between the wide and narrow sections of the pipe?

  58. Analytic Geometry

    Water spouts from a horizontal pipe 12 meters above the ground. Three meters below the line of the pipe, the water trajectory is at a horizontal distance of 5 meters from the water outlet. How far from the water outlet will the stream of the water hit the

  59. Physics

    An organ pipe that is closed at one end has a fundamental frequency of 122 Hz. There is a leak in the church roof, and some water gets into the bottom of the pipe, as shown in the Figure. The organist then finds that this organ pipe has a frequency of 300

  60. physics

    water in a dam is 15 m deep. a horizontal pipe of 4 cm diameter passes through the wall of the dam below the surface of water. a plug secures the pipe opening. the frictional force between the plug and pipe wall is about?

  61. physics

    The concepts that play roles in this problem are similar to those in Multiple-Concept Example 15, except the fluid here moves upward rather than remaining horizontal. A liquid is flowing through a horizontal pipe whose radius is 0.0215 m. The pipe bends

  62. Physics

    Water is flowing through a horizontal pipe at a rate 0.2 m3/s. The pipe narrows from a radius of 10 cm to 4 cm. What is the change in pressure?

  63. physics

    A horizontal pipe contains water at a pressure of 108 kPa flowing with a speed of 1.5 m/s. The pipe narrows to one-half its original diameter. What are the speed and the pressure of the water when the pipe narrows?

  64. Physics

    Water enters a pipe with a cross sectional area of 3.0 cm^2 with a velocity of 3.0 m/s. The water encounters a constriction where its velocity is 15 m/s. What is the cross sectional area of the constricted portion of the pipe?

  65. physics

    water runs into a house through a 5cm pipe.its pressure at entering the house is 1 times 10^5Pa.the faucent on the second floor 2,5cm above where the water enters the house has an inside diameter of 3cm.when the faucent is in use the flow velocity at the

  66. Physics

    A horizontal pipe contains water at a pressure of 120kPa flowing with a speed of 1.4m/s . The pipe narrows to one-half its original diameter. a) what is the speed of the water? b) what is the pressure of the water? I tried using the continuity equation

  67. Fluid Mechanics

    Water enters a turbo-machine at a velocity 12 ft/s. The flow occurs in the horizontal plane. The inside diameters of the inlet and exit pipes are 1 ft and 2 ft, and the gage pressures at the inlet and exit are 10 psi and 5 psi, respectively. The machine is

  68. Frequency - Physics

    An organ pipe that is closed at one end has a fundamental frequency of 128 Hz. There is a leak in the church roof, and some water gets into the bottom of the pipe, as shown in the Figure. The organist then finds that this organ pipe has a frequency of 217

  69. Physics

    An organ pipe that is closed at one end has a fundamental frequency of 122 Hz. There is a leak in the church roof, and some water gets into the bottom of the pipe, as shown in the Figure. The organist then finds that this organ pipe has a frequency of 300

  70. physics

    A 6.4 cm diameter horizontal pipe gradually narrows to 5.2 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 30.0 kPa and 20.2 kPa , respectively

  71. Physics

    Water at a pressure of 400,000Pa flows through a horizontal pipe at a speed of 1.50 m/s. The pipe narrows to 1/8 its original diameter. What is the flow speed through the narrow section?

  72. physics

    A 6.6 diameter horizontal pipe gradually narrows to 3.6 . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 30.0 and 26.0 , respectively. What is the volume rate of flow? Answer in m^3/s

  73. physics

    Water (η = 1.00E-3 Pa·s) is flowing through a horizontal pipe with a volume flow rate of 0.0153 m3/s. As the drawing below shows, there are two vertical tubes that project from the pipe. Assume that H = 0.0477 m and L = 0.670 m I know how to plug in

  74. physics 203

    Water (p=1000kg/m^3) enters a pipe on the ground with an inside diameter of 2cm at a pressure of 4x10^5 Pa. Then a 1-cm diameter pipe leads the water to a height of 5m above the ground. The flow speed at the inlet is v1=1.5m/s. A) Find the flow speed at

  75. calculus

    Given ensuing information, determine the least cost and the least cost mix of on- and off-shore pipe. The intake facility is in the water 2 miles vertically north of the shoreline The water filtration plant is on land 1 mile vertically south of the

  76. Physics

    I can't seem to figure out this problem...what equation would I use? Thanks! An incompressible, nonviscous fluid is initially at rest in the vertical portion of the pipe, where L = 2.17 m. When the valve is opened, the fluid flows into the horizontal

  77. maths

    A large pipe has a diameter of 9.8×10^2cm.Water flows in the pipe at a speed of 5m s^-1.Find the volume in m^3,of water that flows out from the pipe every second,correct to 2 significant fogures.[Take pai as 3.142]

  78. Engineering

    It is found that ozone reaction in water nearly follows first-order kinetics in ozone concentration decreases by 50% in 12 minutes (t1/2 = 12 min). A water supplier wants to inject ozone into a pipe bringing water to thee water treatment plant to

  79. Maty álgebra

    Avatar la the answer of a plumber has a very long piece of pipe that is used to run city water parallel to a major roadway.The pipe is cut into two two sections.One section of pipe is 12ft.shorter than the other.If 34 of the leght of they shorter pipe is

  80. physics

    The pressure in a section of horizontal pipe with a diameter of 2 cm is 143 kPa. Water flows through the pipe at 2.80 L/ s. If the pressure at a certain point is to be reduced to 103 kPa by constricting a section of the pipe, what should the diameter of

  81. physics

    Water is flowing through a horizontal pipe of varying cross section. At section 1,the diameter is 12cm at a pressure of 80000 Pa. At section 2, the pipe has a diameter of 6cm and the pressure is 60000 Pa. Find the speed of water through sections 1 and 2.

  82. physics

    1.)Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.)A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the larger end of the pipe is

  83. physics

    1.)Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.)A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the larger end of the pipe is

  84. physics

    1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the larger end of the pipe

  85. physics

    1.) water is flowing through a horizontal pipe of varying crosection, the diameter is 12.0 cm at a pressure of 8.0x10^4 Pa. at section 2, the pipe has a diameter of 6.0 cm and the pressure is 6.0x10^4 Pa. find the speed of water through section 1 and 2

  86. physics pls help!

    1.) water is flowing through a horizontal pipe of varying crosection, the diameter is 12.0 cm at a pressure of 8.0x10^4 Pa. at section 2, the pipe has a diameter of 6.0 cm and the pressure is 6.0x10^4 Pa. find the speed of water through section 1 and 2

  87. math

    a water tank is supplied by a pipe of diameter50cm the pipe is replaced by k pipe each of which has diameter 10cm.find k.

  88. Physics

    You are working as a summer intern for the Illinois Department of Natural Resources (DNR) and are assigned to some initial work on water resources project. The department will be overseeing the construction of a dam to create a large fresh water lake that

  89. maths

    Pipe A can fill a pool in 15 minutes and pipe B alone can do it in 10 mibutes. Both the pipe are opened after 4 minutes water from pipe B stop flowing.In how much time will pipe A fill the part of the pool

  90. Physics

    A water pipe is inclined 31.0° below the horizontal. The radius of the pipe at the upper end is 2.00 cm. If the gauge pressure at a point at the upper end is 0.122 atm, what is the gauge pressure at a point 2.70 m downstream, where the pipe has narrowed

  91. physics

    trying to raise a barrel using sections of pipe.The three objects are horizontal cylinders resting on level ground. The barrel has a mass of 100 kg and its diameter is 2.0m. Each pipe has a diameter of 0.50 m. What minimum horizontal force must his feet

  92. PHYSICS!!!

    A straight horizontal pipe with a diameter of 1.0 cm and a length of 46 m carries oil with a coefficient of viscosity of 0.11 N · s/m2. At the output of the pipe, the flow rate is 8.4 10-5 m3/s and the pressure is 1.0 atmosphere. Find the gauge pressure

  93. physics

    Water is flowing in a pipe with a circular cross-section area ,and at all point the water completely fills the pipe.At point 1 ,the cross sectiona are of pipe is 0.070 meter square and the fluid velocity is 3.50 meter per second. a.) what is the fluid

  94. Physics please help!!

    Water is flowing in a straight horizontal pipe of variable cross section. Where the cross-sectional area of the pipe is 3.50·10-2 m2, the pressure is 5.30·105 Pa and the velocity is 0.310 m/s. In a constricted region where the area is 12.90·10-4 m2,

  95. Physics

    A 7.9cm diameter horizontal pipe gradually narrows to 5.9cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0kPa and 21.0kPa , respectively. What is the volume rate of flow? in m3/s please help!

  96. Physics

    A water pipe is made of iron with an outside diameter of 2.5 cm and inside diameter of 2.0 cm. The pipe is used to ground an electric appliance. If a current of 20 A flows from the appliance into the water pipe, what fraction of this current will flow in

  97. physics

    What is the pressure change in water going from a 3.0- cm-diameter pipe to a 1.8- cm-diameter pipe if the velocity in the smaller pipe is 3.0 m/s? Im using the equation pv2^2(A2^2-A1^2)/2A1^2 and get (1000)(3)^2(1.8^2-3^20/(2(3)^2) and get -2880 Pa but I'm

  98. PHYSICS please

    what is the minimum gauge pressure needed in the water pipe leading to a building if the water is to come out of a faucet on the 12th floor, 41m. above the pipe.

  99. Physics

    Determine the minimum gauge pressure needed in the water pipe leading into a building if water is to come out of a faucet on the twelfth floor, 40m above that pipe. Pa?

  100. physics

    Water flows through a 1.2 cm diameter pipe into a 155 L bathtub, which it fills in 8 min.What is the speed of the water in the pipe?

Pages

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. 8
  9. 9
  10. 10
  11. 11
  12. 12
  13. 13
  14. 14
  15. 15
  16. 16
  17. 17
  18. 18
  19. 19
  20. 20