1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to

88,365 results
  1. Physics

    Please someone help..A horizontal pipe 10.0cm in diameter has a smooth reduction to a pipe 5.0cm in diameter. If the pressure of the water in the large pipe is 80000Pa and the pressure in the small pipe is 60000Pa at what rate does water flow through the

  2. physics

    Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in figure below, the pressure is P1 = 1.75X104 Pa and the pipe diameter is 6.00 cm. At another point y = 0.250 m higher, the pressure is P2 = 1.20X104 Pa and the pipe

  3. Physic

    1. Water at a pressure of 3.00 x 10 5th Pa flows through a horizontal pipe at a speed of 1.00 m/s. The pipe narrows to one-fourth its original diameter. What is the speed of the flow in the narrow section? Not sure was successfully posted

  4. physics

    A liquid of density 1354 kg/m^3 flows with speed 2.45 m/s into a pipe of diameter 0.29 m. The diameter of the pipe decreases to 0.05 m at its exit end. The exit end of the pipe is 7.82 m lower than the entrance of the pipe, and the pressure at the exit of

  5. physics

    The water supply of a building is fed through a main entrance pipe 6cm in diameter. A 2cm diameter faucet tap positioned 2m above the main pipe fills a 25 liter container in 30s. (a) What is the speed at which the water leaves the faucet? (b) What is the

  6. Physics

    The water flowing through a 1.9 cm (inside diameter) pipe flows out through three 1.3 cm pipes. (a) If the flow rates in the three smaller pipes are 24, 18, and 13 L/min, what is the flow rate in the 1.9 cm pipe? (b) What is the ratio of the speed of water

  7. maths

    Q: oil flows through a pipe at a rate of 40m3/sec. how long will it take to fill a tank of volume 1.2x10^5m3?

  8. Physics

    Water flows at a speed of 15 m/s through a pipe that has a radius of 0.40 m. The water then flows through a smaller pipe at a speed of 45 m/s. What is the radius of the smaller pipe?

  9. physics

    A 5.4 cm diameter horizontal pipe gradually narrows to 3.7 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 35.0 kPa and 21.0 kPa, respectively. What is the volume rate of flow?

  10. Physics help please**

    A water pipe having a 2.1 cm inside diameter carries water into the basement of a house at a speed of 0.88 m/s and a pressure of 169 kPa. The pipe tapers to 1.0 cm and rises to the second floor 7.1 m above the input point. (a) What is the speed at the

  11. physics

    Water flowing through a 1.9-cm-diameter pipe can fill a 500L bathtub in 5.1min. What is the speed of the water in the pipe?

  12. physics

    A round pipe of varying diameter carries petroleum from a wellhead to a refinery. At the wellhead the pipe's diameter is 56.3 cm (0.563 m) and the flow speed of the petroleum is 13.5 m/s. At the refinery the petroleum flows at 5.65 m/s. What is the volume

  13. Physics

    Water flows into one end of a horizontal, cylindrical pipe at 2.0 m/s. The pipe then narrows until its diameter at the opposite end is only 1/3 of that at the beginning. (a) What is the flow speed at the narrow end of the pipe? (b) What is the pressure

  14. Physic

    Determine the mass flow rate of water through a pipe with a diameter of 3.3 cm when speed at which water travels through the pipe is 2.5 m/s.

  15. Physics

    A horizontal water pipe goes from a large diameter to a small diameter and then back to the first diameter as shown in the figure below. The level of water (8cm in the larger tube and 4 cm in the constricted tube) in the small vertical tubes provides us

  16. Math

    A pool has a uniform circular cross section of radius 5 metre and uniform Dept 1.4 metre it is filled by a pipe which delivers water @ 20 litre per second calculate in minutes the time taken to fill the pool. If the pool is emptied in 42 min by another

  17. physic

    Water flows through a 4.0-cm-diameler horizontal pipe ata speed uf 1.3 m/s. The pipe then narrows down to a diameter of 2.0 cm. Ignoring viscosity, what is the pressure difference between the wide and narrow sections of the pipe

  18. AP Physics - Fluids

    A 6.0-cm diameter horizontal pipe gradually narrows to 4.0 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 32 kPa and 24 kPa, respectively. What is the volume rate of flow? I know to use Bernoulli's

  19. Geometry

    The outside diameter of a pipe is 5 cm. The inside diameter is 4 cm. The pipe is 4 meters long. What is the volume of the material used for this length of pipe?Round your answer to the nearest cubic centimeter. (Hint: be sure that all units are in

  20. Physics

    I just need help with c A long horizontal hose of diameter 4.2 cm is connected to a faucet. At the other end, there is a nozzle of diameter 2 cm. Water squirts from the nozzle at velocity 24 m/sec. Assume that the water has no viscosity or other form of

  21. physics pls help!

    1.) water is flowing through a horizontal pipe of varying crosection, the diameter is 12.0 cm at a pressure of 8.0x10^4 Pa. at section 2, the pipe has a diameter of 6.0 cm and the pressure is 6.0x10^4 Pa. find the speed of water through section 1 and 2

  22. physics

    1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm? The pressure at the larger end of the pipe is

  23. Fluid Mechanics

    Water flows into a cylindrical tank through pipe 1 at a rate of 25 ft/s and leaves through pipe 2 at 10 ft/s and through pipe 3 at 12 ft/s. Pipe 4 is an open air vent. Internal diameters of the pipes are: D1=3 in, D2= 2 in, D3=2.5 in, D4=2 in. Calculate a)

  24. Physics

    A horizontal pipe, 10 cm in diameter, has a smooth reduction to a pipe 5 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, what is the flow speed of the water (in m/s) in the

  25. Physics

    The pressure of water flowing through a 6.5×10−2−m -radius pipe at a speed of 1.8m/s is 2.2 × 105 N/m2 What is the flow rate of the water? What is the pressure in the water after it goes up a 5.2−m -high hill and flows in a 5.0×10−2−m -radius

  26. physics

    1.) water is flowing through a horizontal pipe of varying crosection, the diameter is 12.0 cm at a pressure of 8.0x10^4 Pa. at section 2, the pipe has a diameter of 6.0 cm and the pressure is 6.0x10^4 Pa. find the speed of water through section 1 and 2

  27. maths

    To fill a swimming pool two pipes are to be used.If the pipe of larger diameter I'd used for 4 hours and the pipe of smaller diameter for 9 hours only half the pool can be filled .Find ,how long it would take for each pipe to fill the tank separately, if

  28. physics

    Water flows steadily from an open tank into a pipe. The elevation of the top of the tank is 10.2 m, and the elevation at the pipe is 3.90 m. The initial cross-sectional area of the pipe is 6.40×10^−2 m; and at where the water is discharged from the

  29. physics

    Practice Problem 13.9 Let's begin by looking at a flow problem in which the diameter of a pipe changes along the flow path. We will need to use both the continuity equation and Bernoulli's equation for this problem. Water enters a house through a pipe with

  30. phys

    Water flows steadily from an open tank into a pipe as shown in the figure. The elevation of the top of the tank is 12.3 m, and the elevation at the pipe is 3.80 m. The initial cross-sectional area of the pipe (at point 2) is 5.60×10−2 m^2; and at where

  31. physics

    Water is flowing through a horizontal pipe of varying cross section. At section 1,the diameter is 12cm at a pressure of 80000 Pa. At section 2, the pipe has a diameter of 6cm and the pressure is 60000 Pa. Find the speed of water through sections 1 and 2.

  32. physics

    The pressure in a section of horizontal pipe with a diameter of 2 cm is 143 kPa. Water flows through the pipe at 2.80 L/ s. If the pressure at a certain point is to be reduced to 103 kPa by constricting a section of the pipe, what should the diameter of

  33. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  34. physics

    A horizontal pipe 17.00 cm in diameter has a smooth reduction to a pipe 8.50 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?

  35. ap physics

    A 6.2 cm diameter pipe gradually narrows to 4.0 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 30.0 kPa and 24.0 kPa, respectively. What is the volume rate of flow?

  36. ap physics

    A 6.2 cm diameter pipe gradually narrows to 4.0 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 30.0 kPa and 24.0 kPa, respectively. What is the volume rate of flow?

  37. Engineering

    It is found that ozone reaction in water nearly follows first-order kinetics in ozone concentration decreases by 50% in 12 minutes (t1/2 = 12 min). A water supplier wants to inject ozone into a pipe bringing water to thee water treatment plant to

  38. physics

    Water flows at 0.58 m/s through a pipe 11 cm in diameter when the pressure is 450,000 Pa. Determine the water velocity & the pressure in the pipe if it shrinks down to 5 cm in diameter. You can assume that the pipe is horizontal & ρwater = 1000 kg/m3.

  39. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  40. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  41. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  42. physics

    What is the pressure change in water going from a 3.0- cm-diameter pipe to a 1.8- cm-diameter pipe if the velocity in the smaller pipe is 3.0 m/s? Im using the equation pv2^2(A2^2-A1^2)/2A1^2 and get (1000)(3)^2(1.8^2-3^20/(2(3)^2) and get -2880 Pa but I'm

  43. physics

    Two identical wooden barrels are fitted with long pipes extending out their tops. The pipe on the first barrell is 1 foot in diameter, an the pipe on the second barrell is only 1/2 inch in diameter. When the larger ptpe is fill with water to a height of 20

  44. physics

    Water flows in a cylindrical, horizontal pipe. As the pipe widens to twice its initial diameter the pressure in the pipe changes. Calculate the change in pressure between the wide and narrow regions of the pipe. Give your answer as an expression in terms

  45. physics

    Water flows through a 1.2 cm diameter pipe into a 155 L bathtub, which it fills in 8 min.What is the speed of the water in the pipe?

  46. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  47. FLUID MECHANICS

    Water at temperature of 15°C flows through a pipe of diameter D = 2 cm and into a glass. Determine i. The minimum time taken to fill in a 0.5 L glass full with water if the flow in the pipe is to be laminar. ii. The maximum time taken to fill the glass if

  48. physics

    1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the larger end of the pipe

  49. physics

    1.)Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.)A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the larger end of the pipe is

  50. math

    Water flows through a pipe with the inner diameter of 20cm at a speed of 1m/s. How long does it take for the water flowing out from the pipe to fill a cylindrical tank with the base radius of 0.8m and the height of 0.5m?

  51. physics

    Water flows through a 4.0-cm-diameter horizontal pipe at a speed of 1.3m/s . The pipe then narrows down to a diameter of 2.0cm . Ignoring viscosity, what is the pressure difference between the wide and narrow sections of the pipe?

  52. Physics

    Water flows under pressure from one pipe into a second pipe having half the diameter. The volume flow rate in the narrow pipe is ________ that in the wide pipe, and the speed of the water in the narrow pipe is _______ that in the wide pipe

  53. physics

    Water flows at speed of 4.2 m/s through a horizontal pipe of diameter 3.4 cm. The gauge pressure P1 of the water in the pipe is 1.5 atm. A short segment of the pipe is constricted to a smaller diameter of 2.4 cm. What is the gauge pressure of the water

  54. Physics

    Water at a pressure of 3.90 atm at street level flows into an office building at a speed of 0.45 m/s through a pipe 5.60 cm in diameter. The pipes taper down to 2.10 cm in diameter by the top floor, 26.0 m above. Calculate the water pressure in such a pipe

  55. physics

    A horizontal pipe (Venturi Tube) 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.0 x 105 Pa and the pressure in the smaller pipe is 3.0 x 104 Pa, at what rate does water flow

  56. Physics

    A pipe carrying water is laid out over level ground. One segment of the pipe has a diameter of 2.22 cm and the next segment has a diameter of 1.82 cm. In the wider segment, the water pressure is 83,700 Pa and the water is moving at 2.77m/sec. 1-what is the

  57. Physics

    A 0.8 m diameter tank is filled with water to a depth of 2.2 m and is open to the atmosphere at the top. The water drains through a 1.0 cm diameter pipe at the bottom; that pipe then joins a 1.5 cm diameter pipe open to the atmosphere, as shown in Fig.

  58. physics

    A 6.4 cm diameter horizontal pipe gradually narrows to 5.2 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 30.0 kPa and 20.2 kPa , respectively

  59. physics

    A 6.6 diameter horizontal pipe gradually narrows to 3.6 . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 30.0 and 26.0 , respectively. What is the volume rate of flow? Answer in m^3/s

  60. physics, buoyance

    Water flows at a rate of 25L/min through a horizontal 8.0-cm-diameter pipe under a pressure of 5.7Pa . At one point, calcium deposits reduce the cross-sectional area of the pipe to 40cm2 . Part A What is the pressure at this point? (Consider the water to

  61. algebra

    A certain toilet tank can be emptied in 6 sec through its drain when it is flushed. This happens at the same time that the water is flowing in through the inlet pipe. Withthe drain closed, the inlet pipe canfill the tank in 30 sec. How long would it take

  62. physics

    A horizontal pipe 17.00 cm in diameter has a smooth reduction to a pipe 8.50 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?

  63. Physics

    Water flowing through a 2.8 cm-diameter pipe can fill a 200 L bathtub in 5.8 min.What is the speed of the water in the pipe?

  64. FLUID MECHANICS

    Water flows at a rate of 0.040 m3/s in a 0.15 m diameter pipe that contains a sudden contraction section to a 0.06 m diameter pipe. Determine the pressure drop across the contraction section. Determine also the pressure difference due to the losses.

  65. Physics

    Water from the dead sea flows into a pipe of diameter 18cm at a velocity of 5.0m s at pressure 4.0atm. The pipe reduces to a diameter of 10cm at a point 3.5m above. a)Determine the rate of flow. b)Determine the velocity at the top section. c)Determine the

  66. physics 203

    Water (p=1000kg/m^3) enters a pipe on the ground with an inside diameter of 2cm at a pressure of 4x10^5 Pa. Then a 1-cm diameter pipe leads the water to a height of 5m above the ground. The flow speed at the inlet is v1=1.5m/s. A) Find the flow speed at

  67. Physics

    A 7.9cm diameter horizontal pipe gradually narrows to 5.9cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0kPa and 21.0kPa , respectively. What is the volume rate of flow? in m3/s please help!

  68. Engineering

    Your green house irrigation sytem is plumbed with 3/4" pvc pipe from which 1/2" branch lines are routed to each row of plants. if the city supplies water that flows at 3ft/sec what is the velocity of the water at plants level? WEhat is the flow rate in

  69. physics

    1.)Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.)A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the larger end of the pipe is

  70. maths

    A large pipe has a diameter of 9.8×10^2cm.Water flows in the pipe at a speed of 5m s^-1.Find the volume in m^3,of water that flows out from the pipe every second,correct to 2 significant fogures.[Take pai as 3.142]

  71. physics

    Water flows through a 1.2 cm diameter pipe into a 155 L bathtub, which it fills in 8 min.What is the speed of the water in the pipe?

  72. Physics

    Water at a pressure of 400,000Pa flows through a horizontal pipe at a speed of 1.50 m/s. The pipe narrows to 1/8 its original diameter. What is the flow speed through the narrow section?

  73. computers

    1. Water at a pressure of 3.00 x 10 5th Pa flows through a horizontal pipe at a speed of 1.00 m/s. The pipe narrows to one-fourth its original diameter. What is the speed of the flow in the narrow section?

  74. Physics

    Water at a pressure of 4.20 atm at street level flows into an office building at a speed of 0.65 m/s through a pipe 6.60 cm in diameter. The pipes taper down to 2.20 cm in diameter by the top floor, 28.0 m above. Calculate the water pressure in such a pipe

  75. Physics

    A liquid of density 1.23 × 103 kg/m3 flows steadily through a pipe of varying diameter and height. At location 1 along the pipe the flow speed is 9.23 m/s and the pipe diameter is 1.07 × 101 cm. At location 2 the pipe diameter is 1.71 × 101 cm. At

  76. physics

    A horizontal pipe (Venturi Tube) 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 2.0 x 105 Pa and the pressure in the smaller pipe is 5.0 x 104 Pa, at what rate does water flow

  77. Physics

    Water is descending in a vertical pipe of diameter 7 cm and open to the atmosphere. At a lower point the water flows into a smaller pipe of diameter .84 cm. At a certain instant the depth of the water just above the narrowing point is 30 cm and the water

  78. physics

    Water is descending in a vertical pipe of diameter 7 cm and open to the atmosphere. At a lower point the water flows into a smaller pipe of diameter .84 cm. At a certain instant the depth of the water just above the narrowing point is 30 cm and the water

  79. Physics

    A water pipe is made of iron with an outside diameter of 2.5 cm and inside diameter of 2.0 cm. The pipe is used to ground an electric appliance. If a current of 20 A flows from the appliance into the water pipe, what fraction of this current will flow in

  80. Physics

    A horizontal pipe contains water at a pressure of 120kPa flowing with a speed of 1.4m/s . The pipe narrows to one-half its original diameter. a) what is the speed of the water? b) what is the pressure of the water? I tried using the continuity equation

  81. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  82. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  83. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  84. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place. When Fluid is entering the

  85. physics

    A horizontal pipe contains water at a pressure of 108 kPa flowing with a speed of 1.5 m/s. The pipe narrows to one-half its original diameter. What are the speed and the pressure of the water when the pipe narrows?

  86. algebra

    A pipe manufacturer makes pipes of four different sizes. The diameter of each pipe is two times the diameter of the pipe of the next smaller size. The diameter of the biggest pipe is 16 centimeters. What is the diameter of the pipe of the smallest size?

  87. algebra

    A pipe manufacturer makes pipes of four different sizes. The diameter of each pipe is two times the diameter of the pipe of the next smaller size. The diameter of the biggest pipe is 16 centimeters. What is the diameter of the pipe of the smallest size?

  88. Physics

    Water flowing through a 2.8 cm-diameter pipe can fill a 200 L bathtub in 5.8 min.What is the speed of the water in the pipe?

  89. Physics

    Water flowing through a 2.8 cm-diameter pipe can fill a 200 L bathtub in 5.8 min.What is the speed of the water in the pipe?

  90. Physics

    Water flowing through a 2.8 cm-diameter pipe can fill a 200 L bathtub in 5.8 min.What is the speed of the water in the pipe?

  91. maths

    Water flows through cylinder pip of internal diameter 7cm at 2m per second. If the pipe is always half full, them what is the volume of water (in liters) discharged in 10 minutes?

  92. physics

    Water flows at 0.865 m/s from a hot water heater, through a 450kPa pressure regulator. The pressure in the pipe supplying an upstairs bathtub 3.70 m above the heater is 414kPa . What's the flow speed in this pipe?

  93. math

    water flows out through a circular pipe whose internal diameter is 2 cm at the rate of 6 metres per second into a cylindrical tank. the radius of whose base is 60 cm. find the rise in the level of water in 30 minutes

  94. math

    A cylindrical pipe 2 ½ metres long has an internal diameter of 21 millimetres and an external diameter of 35 millimetres. The density of the material that makes the pipe is 1.25 g/cm‘. Calculate the mass of the pipe in kilograms. (Take n = 22/7)

  95. physics

    Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in the figure below, the pressure is P1 = 1.85 104 Pa, and the pipe diameter is 5.0 cm. At another point y = 0.30 m higher, the pressure is P2 = 1.05 104 Pa and the pipe

  96. physics

    water 20 degrees celsius flows through a 25 mm diameter pipe at a rate of 50 liters per minute. is this laminar or turbulant flow or both?

  97. Physics

    Lubricating oil, with a relative density of 0.79, flows around a 90¨¬ bend. The pipe diameter is 0.45m, and the oil has a pressure head of 7m and the flow is 1.7m3/s. Find the force exerted by the oil on the bend. Oil density = 0.79 X 103 Volumetric mass

  98. Physics

    Lubricating oil, with a relative density of 0.79, flows around a 90¨¬ bend. The pipe diameter is 0.45m, and the oil has a pressure head of 7m and the flow is 1.7m3/s. Find the force exerted by the oil on the bend. Oil density = 0.79 X 103 Volumetric mass

  99. physics

    Water flows at 0.830 m/s from a hot water heater, through a 450-kPa pressure regulator. The pressure in the pipe supplying an upstairs bathtub 3.70 m above the heater is 414-kPa. 1. What's the flow speed in this pipe?

  100. physics

    Water flows at 0.860m/s from a hot water heater, through a 450-kPa pressure regulator. The pressure in the pipe supplying an upstairs bathtub 3.70 m above the heater is 414-kPa. What's the flow speed in this pipe?

Pages

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. 8
  9. 9
  10. 10
  11. 11
  12. 12
  13. 13
  14. 14
  15. 15
  16. 16
  17. 17
  18. 18
  19. 19
  20. 20