Physics

Two Rods of equal length have same temperature difference between their ends. If their thermal conductivities are K1 and K2 and their areas of cross section are A1 and A2 respectively, Find the condition that will ensure equal rates of flow of heat through both the rods.

  1. 👍 0
  2. 👎 0
  3. 👁 264
  1. K1/k2=A2/A1

    1. 👍 0
    2. 👎 0
  2. Correct answer

    1. 👍 0
    2. 👎 0

Respond to this Question

First Name

Your Response

Similar Questions

  1. science

    A slab of a thermal insulator is 100 cm² in cross section and 2 cm thick. Its thermal conductivity is 2.4 x 10-4 cal/s.cm.°C. If the temperature difference between the opposite faces is 100 degrees Celsius, how much heat flows

  2. Science

    How are temperature and thermal energy related A) Temperature and thermal energy both measure the total kinetic energy in an object. B) Temperature is one factor that determines the thermal energy of an object C) Thermal energy is

  3. PhysicsI

    A windowpane is half a centimeter thick and has an area of 1.0 m2. The temperature difference between the inside and outside surfaces of the pane is 15° C. What is the rate of heat flow through this window? (Thermal conductivity

  4. Physics

    A person makes a quantity of iced tea by mixing 500g of hot tea(c=4190J/(Kg.k) with an equal mass of ice(T=0c, L=333KJ/Kg). assume that mixture has negligible energy exchange with environment. If tea's initial temperature is 90c,

  1. physics

    Air (a diatomic ideal gas) at 30.0°C and atmospheric pressure is drawn into a bicycle pump that has a cylinder with an inner diameter of 2.50 cm and length 70 cm. The down stroke adiabatically compresses the air, which reaches a

  2. chem please help drbob222

    Two objects A and B have the same mass and the same specific heat. Object A is heated from 30°C to 70°C and object B is cooled from 70°C to 30°C. How are the thermal energies of the two objects related after the temperature

  3. statistics

    7. a factory has a machine that makes steel rods. The length of the rods that the machine makes follows a normal distribution curve with a mean of 11.5 feet and a standard deviation of 0.3 feet. The factory manager does not want

  4. science

    Study the scenario.A small container of water with a low temperature is poured into a large container of water with a higher temperature. Which choice correctly explains what happens to the thermal energy of these systems? A)The

  1. Physics HELP!!

    Three masses are connected by massless rigid rods. Rods AC and CB have length l= 44.8cm. If massA=280.0g, massB=386.0g, and massC=739.0g, what are the coordinates of the center of mass? (Enter your answer for the x coordinate

  2. PHYSICS

    Two wires have the same cross-sectional area and are joined end to end to form a single wire. The first wire has a temperature coefficient of resistivity of α1 =0.00603 (C°)-1 and a resistivity of 5.00 x 10-7Ω m. For the

  3. physics

    The ends of the two rods shown in the figure are separated by 2.97 mm at 24.3 °C. The left-hand rod is brass and 1.21 m long; the right-hand rod is steel and 1.21 m long. Assuming that the outside ends of both rods rest firmly

  4. physics please helpp

    The ends of the two rods shown in the figure are separated by 2.97 mm at 24.3 °C. The left-hand rod is brass and 1.21 m long; the right-hand rod is steel and 1.21 m long. Assuming that the outside ends of both rods rest firmly

You can view more similar questions or ask a new question.