# Engineering

Designation of clamper circuit:

Input Square Wave is described as follow:
V max : 20V
V min : -15v
Frequency : 10kHz

Design a clamper circuit to shift its referecence point so that its reference point is -10V.
Specify all component values and part numbers(if any) used in your design. Show all calculation clearly. Justify any assumption made.

That was the question given. I want to know that in negative clamping this wave so that its reference point goes down to 10v, what should be done? like what should increase or what should decrease? additional capacitors? don't have to give me the specific value but please help me by telling me the rough idea of where i should start and what i should be looking for or notice. Please help me with this as i am totally lost. thank you so much!!

1. 👍
2. 👎
3. 👁
1. I would use a capacitor to clamp the output. The output capacitor will have a 5v charge on it, adding to the wave form. The time constant for discharging should be very long, so as to not affect the shape of the waveform. You can use a zener diode to stabalize the capacitor voltage.

1. 👍
2. 👎
👤
bobpursley

## Similar Questions

1. ### Science

One light bulb in a string of lights goes out this causes all other lights in string to go out. This is example of A. Resistor B. parallel circuit C. Closed circuit***** D. Series circuit When a switch is turned from the off to

2. ### Physics

Thanks for any help :) Four 20 ohm resistors are connected in parallel and the combination is connected to a 20V emf device. The current is: A) 0.25A B) 1.0 A C) 4.0 A D) 5.0 A E) 100 E Parallel circuits: I know that the voltage

3. ### discrete math

Q: Consider a digital circuit that reads an n-bit input string and writes a 1bit output. Two circuits are considered different if they have a different output for some input string, otherwise they are considered the same (i.e. two

4. ### Physics

If an earthquake wave having a wavelength of 13 km caused the ground to vibrate 10 times each minute, what is the speed of the wave? 1.2 km/s 2.2 km/s 220 m/s 22 m/s If the amplitude in a sound wave is doubled, by what factor does

1.D 2.A 3.A 4.im not sure please help 5.false One light bulb in a string of lights goes out. This causes all of the other lights in the string to also go out. This is an example of a A. resistor. B. parallel circuit. C. closed

2. ### Science

9. FM signals travel as changes in (1 point) A.the speed of the wave. B.the amplitude of the wave. C.the frequency of the wave.*** D.the loudness of the wave.

3. ### Science

How is a parallel circuit different from a series circuit? A: A parallel circuit only has one path for the circuit to take. B: A parallel circuit has more than one path for the circuit to take.** C: A parallel circuit has a broken

4. ### Science

To find the current in a complex circuit, it is necessary to know the potential difference in each device in the circuit. current in each device in the circuit. equivalent resistance of the circuit. number of branches in the

Please help check my answers I really want to make a 100%! 1. A mechanical wave moves through a medium, which can be (1 point) A. a liquid. B. a solid. C. a gas. D. all of the above

2. ### Science

Which choice most accurately explains the role of a circuit component in preventing a circuit from getting too hot and catching fire? (Select all that apply) 1-A fuse can be used to prevent a circuit from getting too hot. It will

3. ### Physics

The speed of a transverse wave on a string is 450 m/s, while the wavelength is 0.18 m. The amplitude of the wave is 2.0 mm. What is the total up and down distance moved by the wave-particle for each cycle of the wave? What is the

4. ### physics question

What factors affect the frequency of a wave? A. the amplitude B. the energy of the wave C. the wavelength of the wave D. the material through which it travels E. the velocity of the wave I said C,D, and E. Should there be anything