# Physics

A horizontal segment of pipe tapers from a cross sectional area of 50.0 cm^ 2 to 0.500 cm^2. The pressure at the larger end of the pipe is 1.20x 10^5 Pa, and the speed is 0.040 m/s. what is the pressure at the narrow end of the segment?

1. 0
2. 0
3. 10

## Similar Questions

1. ### physics

1.)Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.)A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the

asked by slayer on November 23, 2008
2. ### physics

1.)Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.)A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at the

asked by slayer on November 23, 2008
3. ### physics

1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm^2. The pressure at

asked by slayer on November 23, 2008
4. ### physics

1.) Water flows from a 2 cm diameter pipe, at a speed of 0.35m/sec. How long will it take to fill a 10 liter container? 2.) A horizontal segment of pipe tapers from a cross-sectional area of 50 cm^2 to 0.5 cm? The pressure at the

asked by Akitsuke on November 23, 2008
5. ### Physics

A horizontal segment of pipe tapers from a cross sectional area of 50 cm2 to 0.5 cm2. The pressure at the larger end of the pipe is 1.34 105 Pa and the speed is 0.038 m/s. What is the pressure at the narrow end of the segment?

asked by Dante on November 7, 2007
6. ### physics

A horizontal segment of pipe tapers from a cross sectional area of 50 cm2 to 0.5 cm2. The pressure at the larger end of the pipe is 1.26 105 Pa and the speed is 0.029 m/s. What is the pressure at the narrow end of the segment? Pa

asked by Malika on April 9, 2012
7. ### physics

Water flows steadily from an open tank into a pipe. The elevation of the top of the tank is 10.2 m, and the elevation at the pipe is 3.90 m. The initial cross-sectional area of the pipe is 6.40×10^−2 m; and at where the water

asked by AE on December 1, 2009
8. ### phys

Water flows steadily from an open tank into a pipe as shown in the figure. The elevation of the top of the tank is 12.3 m, and the elevation at the pipe is 3.80 m. The initial cross-sectional area of the pipe (at point 2) is

asked by ami on December 9, 2009
9. ### Physics

Alcohol flows smoothly through a horizontal pipe that tapers in cross-sectional area from A1 = 41.9 cm2 to A2= A1/3. The pressure difference Δp between the wide and the narrow sections of the pipe is 11.1 kPa. What is the volume

asked by Sammy on December 2, 2009
10. ### physics

A venturi meter is a device for measuring the speed of a fluid within a pipe. The drawing shows a gas flowing at a speed v2 through a horizontal section of pipe whose cross-sectional area A2 = 0.0900 m2. The gas has a density of

asked by johnny on December 6, 2010

More Similar Questions