1. Questions

ap chem

could you please check my work?
what is the volume of one mole of solid iron at 25 degrees c?

1 mol Fe/.141 mol/cm^3 = 7.10 cm^3

(the .141 came from converting the density in to moles)

is that correct?

then the next step in the problem is to find the volume of 1 mol of Fe atoms assuming each atom to be spherical. the atomic radius is 0.126 nm.

so i calculated:
4/3 pi (0.126 nm)^3 = .00838 nm^3

is that correct?
thank you for your help.

  1. 👍
  2. 👎
  3. 👁
John

  1. I don't know how you converted density to mols/cc and 55.85/0.141 is not 7.10 BUT 55.85/7.871 = 7.095 g/cc which rounds to 7.10 g/cc and that is the correct answer.
    As for the volume, after reading some of your earlier posts, especially the one about the crystal structure of iron, I wonder if the problem intended for you to go through the unit cell business.

    1. 👍
    2. 👎
    DrBob222

  2. By the way, if you are the same John that posted earlier about the boiling point of 2-propanol, I have posted a response to that at the original post. There are two or three things wrong with the way you did it although the Clausius-Clapeyron equation is the correct way to go.

    1. 👍
    2. 👎
    DrBob222

  4. well i thought that by knowing the cubic structure maybe i could work backwards but it just ended up confusing me even more.

    1. 👍
    2. 👎
    John

  5. 6- chloro- 3- hexene

    1. 👍
    2. 👎
    Anonymous

Respond to this Question

First Name

Your Response

Similar Questions

  1. chemistry

    What is the balanced formula for Solid iron 3 oxide reacts with hydrogen gas to form solid iron and liquid water?

  2. chemistry

    You are analyzing a solid isolated from a reaction and find that its boiling point is over 1000 ∘C. You dissolve the compound in water solution and recrystallize it to produce some solid crystals that you use to determine that

  3. calculus

    Consider the solid obtained by rotating the region bounded by the given curves about the x-axis. y = 9 - 9x^2 , y = 0 Find the volume V of this solid. Sketch the region, the solid, and a typical disk or washer. Any help or tips

  4. Chemistry

    Write and balance equations for the following reactions. A)Iron metal and Chlorine gas react to form solid iron(III) chloride. B)Solid aluminum carbonate decomposes to form solid aluminum oxide and carbon dioxide gas. C)Solid

  1. chemistry

    You add 8.7g of iron to 21.30mL of water and observe that the volume of iron and water together is 22.41mL . Calculate the density of iron.

  2. Calculus

    A ball of radius 12 has a round hole of radius 6 drilled through its center. Find the volume of the resulting solid. I tried finding the volume of the sphere and the volume of the cyclinder then subtract however that did not work.

  3. calculus review please help!

    1) Find the area of the region bounded by the curves y=arcsin (x/4), y = 0, and x = 4 obtained by integrating with respect to y. Your work must include the definite integral and the antiderivative. 2)Set up, but do not evaluate,

  4. Last Question Plz helppp:((im soo sleepy!!:(

    1)The reaction between solid sodium and iron(III) oxide, Fe2O3(s), is one in a series of reactions that occurs when an automobile air bag inflates. 6Na(s) + Fe2O3(s) -> 3Na2o(s) + 2Fe(s) If 100.0 g of iron(III) oxide are used in

  1. science

    3. Hydrobromic acid dissolves solid iron according to the following reaction: Fe(s) + 2HBr(aq) ---> FeBr2(aq) + H2(g) What mass of HBr (in g) would you need to dissolve a 3.2 gram pure iron bar on a padlock? What mass of H2 would

  2. CHEMISTRY

    Which of the following solutions contain the greatest total ion concentration? a) one mole of potassium chloride dissolved in 1.0L of solution b)one mole of sodium phosphate dissolved in 1.0L of solution c)one mole of ammonium

  3. physics

    An iron wire has a cross-sectional area equal to 1.20 10-5 m2. Carry out the following steps to determine the drift speed of the conduction electrons in the wire if it carries a current of 34.0 A. (a) How many kilograms are there

  4. Chemistry

    A solution of I2 was standardized with ascorbic acid. Using a 0.1000-g sample of pure ascorbic acid (C6H8C6), 25.32 ml of I2 were required to reach the starch end point. What is the molarity of the iodine solution? Please check to

You can view more similar questions or ask a new question.