machines

how do disc grinders work?


My disk grinder has a series AC motor attached to a rubber disk upon which the grinding sheet is attached. The grinding sheet I use is carbide glued to paper. The carbide coated sheet rotates against the metal, usually a weld I am smoothing, and the metal wears away faster than the carbide coating.

  1. 👍 0
  2. 👎 0
  3. 👁 221

Respond to this Question

First Name

Your Response

Similar Questions

  1. Physics

    A small disk of radius R1 is mounted coaxially with a larger disk of radius R2. The disks are securely fastened to each other and the combination is free to rotate on a fixed axle that is perpendicular to a horizontal frictionless

    asked by John on December 2, 2011
  2. Physics (torque, if possible)

    An electric motor turns a flywheel through a drive belt that joins a pulley on the motor and a pulley that is rigidly attached to the flywheel. The flywheel is a solid disk with a mass of 80.0kg and a dimaeter of 1.25m. It turns

    asked by Anderson on April 18, 2007
  3. Physics

    The figure shows an arrangement in which four disks are suspended by cords. The longer, top cord loops over a frictionless pulley and pulls with a force of magnitude 93.4 N on the wall to which it is attached. The tensions in the

    asked by Nick on February 23, 2016
  4. physics

    A string is wrapped around a uniform disk of mass M = 1.6 kg and radius R = 0.10 m. (Recall that the moment of inertia of a uniform disk is (1/2)MR2.) Attached to the disk are four low-mass rods of radius b = 0.17 m, each with a

    asked by sara on July 31, 2014
  5. Physics

    A spring has a force constant of 100N/m and an unstretched lenght of .07 m. One end is attached to a post that is free to rotate in the center of a smooth table. The other end is attatched to a 1 kg disc moving in uniform circular

    asked by Tammy on March 25, 2007
  1. physics

    A disk with a mass of 29 kg and a radius of 31 cm is mounted on a frictionless horizontal axle. A string is wound many times around the disk and then attached to a 70-kg block, as shown in the figure. Find the acceleration of the

    asked by Anonymous on March 25, 2011
  2. physics

    A force of 100 N is applied tangentially to a disk of radius 10 cm and mass 0.5 kg. the disk is initially at rest. What is the angular acceleration of the disk? How many revolutions does the disk goes through after 10 sec. How

    asked by Maa on December 4, 2010
  3. physics

    from a disk of radius R,a concentric circular portion of radius r is cut out so as to leave an annular disc of mass M . the moment of inertia of this annular disc about the axis perpendicular to its plane and passing through its

    asked by Anonymous on December 4, 2013
  4. physics

    A circular disc of radius 'r' carries uniform charge distribution of surface charge density 'A'. If the disc lies on the z = 0 plane, with its axis along the z axis, find the electric field at a point P, along the z axis that

    asked by Anupam on September 18, 2014
  5. physics

    A horizontal disc rotating freely about a vertical axis makes 90 revolutions per minute. A small piece of wax of mass “m” falls vertically on the disk & sticks to it at a distance “r” from the axis. If the number of

    asked by hriday on December 30, 2008
  6. physics

    A box that weighs 725 N is lifted a distance of 20.0 m straight up by a cable attached to a motor. The job is done in 6.5 s. What power is developed by the motor in watts and kilowatts?

    asked by Anonymous on December 12, 2011

You can view more similar questions or ask a new question.