Physics

A closed organ pipe 0.8 m long has a diameter of 7.0 cm. The air in the church is 15oC. What is the fundamental frequency? If the heat is turned up to 20oC, what is the new fundamental frequency? -
HELPHELPHELP<3

  1. 👍 0
  2. 👎 0
  3. 👁 162
  1. Q~Q

    1. 👍 0
    2. 👎 0

Respond to this Question

First Name

Your Response

Similar Questions

  1. Physics

    Assume the length of an organ pipe is L=24cm. You have excited the wave in the tube, and you observe that it has displacement nodes at 4cm, 12cm, and 20cm measured from one end of the pipe. In which harmonic, n, is the air in the

  2. Physics

    Please someone help..A horizontal pipe 10.0cm in diameter has a smooth reduction to a pipe 5.0cm in diameter. If the pressure of the water in the large pipe is 80000Pa and the pressure in the small pipe is 60000Pa at what rate

  3. Physics-Resonance

    A 3.00 m long pipe is in a room where the temperature is 20 C. What is the fundamental frequency if the pipe is closed at one end? Would this count as an open pipe still, or a closed pipe? This is what I did. Wavelength = 2L/n

  4. Fluid Mechanics

    Water flows into a cylindrical tank through pipe 1 at a rate of 25 ft/s and leaves through pipe 2 at 10 ft/s and through pipe 3 at 12 ft/s. Pipe 4 is an open air vent. Internal diameters of the pipes are: D1=3 in, D2= 2 in, D3=2.5

  1. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place.

  2. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place.

  3. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place.

  4. Fluid Mechanics

    Oil (sp. gr.= 0.8) flows smoothly through the circular reducing section shown at 3 ft^3/s. If the entering and leaving velocity profiles are uniform, estimate the force which must be applied to the reducer to hold it in place.

  1. physics

    A liquid of density 1354 kg/m^3 flows with speed 2.45 m/s into a pipe of diameter 0.29 m. The diameter of the pipe decreases to 0.05 m at its exit end. The exit end of the pipe is 7.82 m lower than the entrance of the pipe, and

  2. Physics-Need Help fast!

    Part 1 A 3m long pipe is in a room where the temperature is 20 degrees C. What is the frequency of the first harmonic if the pipe is closed at one end? Part 2 sound traveling in air at 23 degrees C enters a cold front where the

  3. Physics

    An organ pipe that is open a t both ends has a fundamental frequency of 382 Hz. What is the length of an closed end pipe that has a fundamental frequency exactly one octave higher? Report your answer in m.

  4. physics

    Water flows through a 4.0-cm-diameter horizontal pipe at a speed of 1.3m/s . The pipe then narrows down to a diameter of 2.0cm . Ignoring viscosity, what is the pressure difference between the wide and narrow sections of the pipe?

You can view more similar questions or ask a new question.