Questions LLC
Login
or
Sign Up
Ask a New Question
Science
Chemistry
Analytical Chemistry
How do we correct the problem if during TLC development the solvent ran off the plate?
1 answer
Use a shorter time is one way.
You can
ask a new question
or
answer this question
.
Similar Questions
Question: When a TLC plate ws developed, the solvent front ran off the top of the plate. What should be done to correct the
Top answer:
To correct the error when the solvent front runs off the top of a TLC (thin-layer chromatography)
Read more.
When a tlc plate was developed the solvent front ran off the top of the plate, why?
A two component mixture containing a
Top answer:
To address the first question about the solvent front running off the top of the TLC plate, there
Read more.
What is the problem of spotting TOO much sample on a TLC plate initially? Also, why is it bad to have too much solvent in the
Top answer:
Too much sample leads to poor separation of the bands. Too much solvent means the solvent may touch
Read more.
In a thin layer chromatography (TLC)experiment,the TLC plate was pre-developed in the development chamber containing the mobile
Top answer:
I don't know the text book answer but I think the mobile phase should be replaced.
Read more.
Choccamine and mintanol have Rf values of 0.81 and 0.21 respectively. What would the distance in centimetres (cm) between the
Top answer:
Rf value = (distance by unknown/distance by solvent) Substitute and solve for distance by the 0.81
Read more.
Assume your sample spots are 1 cm above the bottom of the TLC plate. What happens if you put the plate in a developing chamber
Top answer:
Wouldn't you think C.
Read more.
When a TLC plate was developed, the solvent front ren off the top of the plate. why?
Top answer:
It was left in the solvent too long or do you know that already.
Read more.
Chromatography
How can I tell which of two mobile phases is more polar? Does the fact that one solvent (e.g. isopropanol/ammonia)
Top answer:
Answered above.
Read more.
Chromatography
How can I tell which of two mobile phases is more polar? Does the fact that one solvent (e.g. isopropanol/ammonia)
Top answer:
I think you can use both methods. The first one if you compare the move up the plate IF you know
Read more.
when 2 propanol was used as the developing solvent, two substances moved with the solvent front (Rf=1) during TLC analysis on a
Top answer:
In TLC (thin-layer chromatography) analysis, substances are separated based on their affinity for
Read more.
Related Questions
in modern printing technology what important type of plate is created a nickel salt solution?
Copper plate •• Printing plate
Question: A student spots an unknown sample on a TLC plate and develops it in dichloromethane solvent. Only one spot, for which
Four runners ran the relay, Bill ran his lap in 22.738 seconds, Troy ran in 21.874 seconds, Grace ran in 20.32 second, and
Question: A student spots an unknown sample on a TLC plate and develops it in pentane solvent. Only one spot, for which the Rf
Consider the following errors that could be made when running TLC. Indicate what should be done to correct the error.
a) a
Question: Consider a sample that is a mixture composed of biphenyl, benzoic acid and benzyl alcohol. The sample is spotted on a
I've done some TLC plates using ethyl acetate with 0.5% glacial acetic acid as a solvent. The structure of these substances
I'm so confused as to how to even begin the problem and where to put whats given to me into an equation.
1) If the value of Kp is
Question: What would happen to the Rf values of the pigments if you were to increase the relative concntration of acetone in the
Consider compounds trans-4-tert-butylcyclohexanol and 4-tert-butylcyclohexanone below. Using silica gel TLC plates, which of
