analytical chemistry

why should EDTA solution be stored in polyethylene container?

  1. 👍 0
  2. 👎 0
  3. 👁 160
  1. As opposed to what kind of bottle?

    1. 👍 0
    2. 👎 0
    posted by DrBob222

Respond to this Question

First Name

Your Response

Similar Questions

  1. chemistry8

    1.why must MgCl2.6H20 be added to the EDTA solution? 2. why should EDTA solution be stored to the polyethylene container? 3. why should HCl be added to calcium carbonate solution? 4. why is it necessary to buffer the solution at

    asked by tan ni on July 17, 2010
  2. Chemistry

    The reaction of a metal ion, M^2+, with EDTA is given in the following equation: M^2+(aq) + Y^4-(aq) MY^2-(aq) The EDTA was standardized with a 0.04 M Zn^2+ solution. 25.05 mL of EDTA solution was used to titrate the Zn^2+

    asked by Miguel on July 20, 2010
  3. analytical chemistry

    An EDTA solution is standardized against a solution of primary standard CaCO3 (0.5622 g dissolve in 1000 ml of solution) and titrating aliquots of it with the EDTA. If a 25.00 ml aliquot required 21.88 ml of the EDTA, what is the

    asked by Anonymous on February 3, 2013
  4. analytical chemistry

    A solution containing both Fe 3+ and Al 3+ can be selectively analyzed for Fe 3+ by buffering to a pH of 2 and titrating with EDTA. Th e pH of the solution is then raised to 5 and an excess of EDTA added, resulting in the

    asked by jody on May 4, 2013
  5. Analytical chemistry

    A 25.0-mL solution of 0.0660 M EDTA was added to a 33.0-mL sample containing an unknown concentration of V3 . All V3 present formed a complex, leaving excess EDTA in solution. This solution was back-titrated with a 0.0450 M Ga3

    asked by Ashley on April 4, 2013
  1. chemistry

    25.00 mL aliquots of the solution from Part 1 are titrated with EDTA to the Eriochrome Black T end point. A blank containing a small measured amount of Mg2+ requires 2.60 mL of the EDTA to reach the end point. An aliquot to which

    asked by saddee on April 28, 2009
  2. Chemistry (titrations)

    15.00 mL of 0.01200 M EDTA were used to titrate 50 mL aliquot solution containing iron (II). How much iron (II) is present in the solution? The answer in the book is 201 ppm. I tried getting the moles of EDTA (n,EDTA = 1.8 x 10^-4

    asked by Nina on March 15, 2014
  3. Chem 2

    A 100-mL sample of water is titrated with EDTA solutions in problem 2. The same amount of Mg2+ is added as previously, and the volume of EDTA required is 31.84mL. What volume of EDTA is used in titrating the Ca2+ in hard water?

    asked by Carlye on February 11, 2014
  4. chem

    H2 stored in a 50.0 L container has a pressure of 500.0 torr. O2 stored in a 25.0 L container has a pressure of 800.0 torr. If both these gases are released together to be stored in a 100.0 L container, what is the total pressure

    asked by bekah on October 10, 2014
  5. Chemistry

    Have have 3 general question regrading Analysis of the hardness of water: 1. What is meant by non-zero blank correction in calculating EDTA?(Whats the effects?) 2. EDTA in an experiment was not dry would it effect the EDTA

    asked by AhmadM on January 30, 2013

More Similar Questions