chemistry

what is the ratio of water drops to EDTA if 2 drops of EDTA was needed to change the color of 20 drops of water with unknown hardness?

a. 10
b. 5
c. 0.1
d. 1.0

  1. 👍 0
  2. 👎 0
  3. 👁 119
asked by alex
  1. Bob Pursley answered below.

    1. 👍 0
    2. 👎 0
  2. Bob pursle answered a very similar question this one has 2 drops and unknown hardness...

    1. 👍 0
    2. 👎 0
    posted by alex

Respond to this Question

First Name

Your Response

Similar Questions

  1. chemistry

    what is the ratio of water drops to EDTA if 2 drops of EDTA was needed to change the color of 20 drops of water with unknown hardness? a. 10 b. 5 c. 0.1 d. 1.0 please explain..

    asked by alex on May 12, 2010
  2. chemistry

    what is the ration of water drops to EDTA (ethylenediamene tetraacetic acid) if 3 drops of EDTA was needed to change the color of 20 drops of water with known hardness?? a. 0.15 b. 1.0 c. 4.0 d. 6.7 am I missing something huge

    asked by alex on May 12, 2010
  3. Chemistry

    Analysis of Tap water (Hardness) 50.00 mL of tap water was transferred to a 250 mL erlenmyer flask. 10mL of NH3/NH4^+ ph 10 buffer was added to the flask, as well as 6 drops of eriochrome black T indicator. This soln was then

    asked by Lauren--PLEASE HELP on November 29, 2009
  4. Chem 2

    A 100-mL sample of water is titrated with EDTA solutions in problem 2. The same amount of Mg2+ is added as previously, and the volume of EDTA required is 31.84mL. What volume of EDTA is used in titrating the Ca2+ in hard water?

    asked by Carlye on February 11, 2014
  5. Chemistry

    Have have 3 general question regrading Analysis of the hardness of water: 1. What is meant by non-zero blank correction in calculating EDTA?(Whats the effects?) 2. EDTA in an experiment was not dry would it effect the EDTA

    asked by AhmadM on January 30, 2013
  6. chemistry

    25.00 mL aliquots of the solution from Part 1 are titrated with EDTA to the Eriochrome Black T end point. A blank containing a small measured amount of Mg2+ requires 2.60 mL of the EDTA to reach the end point. An aliquot to which

    asked by saddee on April 28, 2009
  7. Chemistry

    A 25.00 ml sample of a standard solution containing 1 g of CaCO3/L required 25.20 ml of EDTA to fully complex the Ca present. Calculate the volume of EDTA stoichiometrically equivalent to 1.0 mg of CaCO3. From the volume of EDTA

    asked by Anonymous on March 14, 2010
  8. analytical chemistry

    A solution containing both Fe 3+ and Al 3+ can be selectively analyzed for Fe 3+ by buffering to a pH of 2 and titrating with EDTA. Th e pH of the solution is then raised to 5 and an excess of EDTA added, resulting in the

    asked by jody on May 4, 2013
  9. Chemistry

    The following data was obtained from titrating a solution containing 25 mL of 0.0100 M MgCl2 solution, 1 mL of NH3OH buffer, and 10 drops of Calmagite with EDTA. Calculate the concentration of EDTA. Report the answer with three

    asked by shannon on May 13, 2013
  10. analytical chemistry

    An EDTA solution is standardized against a solution of primary standard CaCO3 (0.5622 g dissolve in 1000 ml of solution) and titrating aliquots of it with the EDTA. If a 25.00 ml aliquot required 21.88 ml of the EDTA, what is the

    asked by Anonymous on February 3, 2013

More Similar Questions