Chemistry

Acid-Base Titrations

a) How will the concentration of NaOH be affected if during the titration some of the solid potassium hydrogen phthalate was spilled during the transfer? Will the concentration of the standardized NaOH increase, decrease, or have no effect?

b) How will the molar mass of an unknown acid be affected if some of the solid remained after the titration was complete? Will the concentration of the molar increase, decrease, or have no effect?

c) How will the concentration of acetic acid in vinegar be affected if the liquid retained in the pipet is blown out? Will the concentration of acetic acid in vinegar increase, decrease, or have no effect?

d) How will the concentration of acetic acid in vinegar be affected if during the titration an air bubble appears in the tip of the buret? Will the concentration increase, decrease, or have no effect?

  1. 👍 0
  2. 👎 0
  3. 👁 655
  1. Look at how you calculated the M of the NaOH.
    You had KHP and moles= grams/molar mass.
    Then M NaOH = moles/L
    So if some of the KHP was spilled, that means grams was too low, which makes moles too low and if moles is too low when plugged into M NaOH, then moles/L will be too low and M will be too low.
    The others are done with the same kind of reasoning.

    1. 👍 0
    2. 👎 0
  2. KHP?

    1. 👍 0
    2. 👎 0
  3. C and D are worded extremely poor.

    1. 👍 0
    2. 👎 0

Respond to this Question

First Name

Your Response

Similar Questions

  1. Chemistry

    SOMEBODY PLEASE HELP ME! This is my last question for the chemistry and thank you. :D A BS Medical Technology student was asked to determine the molecular weight of a diprotic acid using acid-base titration. This student performed

    asked by Shiro on May 6, 2020
  2. Chemistry

    40.0 ml of an acetic acid of unknown concentration is titrated with 0.100 M NaOH. After 20.0 mL of the base solution has been added, the pH in the titration flask is 5.10. What was the concentration of the original acetic acid

    asked by Bob on April 10, 2011
  3. Chemistry

    A BS Medical Technology student was asked to determine the molecular weight of a diprotic acid using acid-base titration. This student performed four trials. Firstly, the student used potassium hydrogen phthalate (KHP, 204.22

    asked by el on May 14, 2020
  4. Chemistry

    1.) Watch the animation, and observe the titration process using a standard 0.100 M sodium hydroxide solution to titrate 50.0 mL of a 0.100 M hydrochloric acid solution. Identify which of the following statements regarding

    asked by LuigiR on November 19, 2015
  1. CHEMISTRY PLEASE HELP

    a) How will the concentration of NaOH be affected if during the titration some of the solid potassium hydrogen phthalate was spilled during the transfer? Will the concentration of the standardized NaOH increase, decrease, or have

    asked by Josh on October 24, 2011
  2. Analytical chemistry

    A dilute perchloric acid solution was standardized by dissolving 0.2445 g of primary standard sodium carbonate in 50 mL of the acid, boiling to eliminate CO2, and back-titrating with 4.13mL of dilute NaOH. In a separate titration

    asked by Gloria on August 1, 2013
  3. Chemistry

    1) You are given solutions of HCl and NaOH and must determine their concentrations. You use 37.0mL of NaOH to titrate 100mL of HCl and 13.6 mL of NaOH to titrate 50.0mL of 0.0782 M H2SO4. Find the unknown concentrations. Molarity

    asked by Ashley on October 4, 2010
  4. Chemistry PLEASE HELP!

    Check all of the following statements which are TRUE for a titration. Select one or more: a. A suitable primary standard must be available. b. The concentration of the solution in the buret (the titrant) must be known before the

    asked by Sophie on May 5, 2013
  1. Chemistry Titration Lab HELP!

    Hi everyone! I just got a new lab that I MUST complete today, and it's about titration- I have absolutely no clue how to do it, it just doesn't make sense to me! I hope that someone can help explain to me how to do it so I can

    asked by Angel on June 11, 2008
  2. Chemistry

    How to solve titration problem for HC2H3O2 + NaOH= NaC2H3O2 + H2O The M of NaOH= 0.427 The volume of NaOH= 17.30mL 10.00mL of acid The second titration calculation is: The M of NaOH= 0.427 The volume of NaOH=34.60mL 20.00mL of

    asked by John on September 27, 2012
  3. Chemistry

    15.00mL sample of a solution of H2SO4 of unknown concentration was titrated with 0.3200 N NaOH. The titration required 21.30mL of the base. What was the normality of the acid solution? what was the molarity of the acid solution?

    asked by Mark on October 5, 2015
  4. Chemistry

    We will calculate the amount of acid to use in each titration. Assume that you are using 0.0512 M NaOH(aq). A good volume of NaOH(aq) to use per titration is 15 mL. From this molarity and volume, the moles of NaOH can be

    asked by Erin on February 8, 2017

You can view more similar questions or ask a new question.