Chemistry

A little confused on this question... I think I would need to take the solute and put it over the solvent, and then use molar mass. Confused on how density plays into this problem.

Sucrose is very soluble in water. At 25ºC, 211.4 grams of sucrose will dissolve in 100 g of water. Given that the density of the saturated sucrose solution is 1.34 g/mL, what is the molarity of the solution? The molar mass of sucrose is 342 g/mol.

  1. 👍
  2. 👎
  3. 👁
  1. M = mols/L solution. The density is given so that you can convert the 100 g of solution into a volume.
    mols = grams sucrose/molar mass sucrose = ?
    mass solution = (100+211.4) = volume in mL x density in g/ml. Substitute and solve for volume in mL and convert to L, then find M.

    1. 👍
    2. 👎

Respond to this Question

First Name

Your Response

Similar Questions

  1. biology

    Compare hypertonic, hypotonic, and isotonic solutions. When an environment is hypotonic, what happens to the cell?1pt a.The cell has more solute, so solvent moves from outside the cell to inside, causing the cell to swell. b.The

  2. Chemistry

    An aqueous solution is 8.50% ammonium chloride, NH4Cl, by mass. The density of the solution is 1.024g/mL. Calculate the molality, mole fraction, and molarity of NH4Cl in the solution. I know the formulas needed but I'm not sure

  3. calculus

    If d/dx(f(x))=g(x) and d/dx(g(x))=f(x^2) , then d^2/dx^2(f(x^3)) , then d2dx2(f(x3))= A f(x^6) B g(x^3) C 3x^2g(x^3) D 9x^4f(x^6) + 6xg(x^3) E f(x^6) + g(x^3) I understood what the first half of the question said, but then I was

  4. To Sheryl: polarity

    The exact question is: Benzyl alcohol (bp 205 degree C) was selected by a student to crystallize fluorenol (mp 153-154 degrees C) because the solubility characteristics of this solvent are appropriate. However, this solvent is not

  1. College Chemistry

    In this lab: we demonstrated the method of evaporation of a saturated sodium chloride solution. The following question ask: 1) why is sodium chloride chosen for the solute? 2)Suggest reasons why the following were not chosen for

  2. Org. Chem.

    Is there a correlation between the values of the distribution coefficients and the polarities of the three compounds? Explain. Place 0.050 g of one of the solids (benzoic acid, succinic acid, or sodium benzoate) in a vial and add

  3. Chemistry

    I need help please I am so confused. How much dry solute would you take to prepare each of the following solutions from the dry solute and the solvent? I know the MM of KCl is 74.55 107g of 0.535m KCl

  4. Chemistry

    What would be the effect of each of the following on the calculated molecular weight of the solute? a) some cyclohexane evaporated while the freezing point of pure cyclohexane was being measured. ( i think it would be higher)

  1. Bio

    How much solute is required to make 600mL of a 0.4 M solution of Tris buffer? FW of Tris Buffer= 121.1g Work: Molarity equation= moles of solute/ liters of solution Step 1: 121.1 g / 121.14 g/mol TB = 0.9996 mol TB Step 2:

  2. Chemistry

    The units of parts per million (ppm) and parts per billion (ppb) are commonly used by environmental chemists. In general, 1 ppm means 1 part of solute for every 106 parts of solution. (Both solute and solution are measured using

  3. AP Chem

    1. Van't Hoff factors depend on the concentrations of the dissolved solute species. Why would a dilute solution have a Van't Hoff factor closer to the ideal value? a. because in dilute solutions solute species are less likely to

  4. Chemistry

    two solutions are prepared using the same solute solution a: 0.27g of the solute disolves in 27.4g of t-butanol solution b: 0.23g of the solute disolves in 24.8g of cyclohexane which solution has the greatest freesing point

You can view more similar questions or ask a new question.