Questions LLC
Login
or
Sign Up
Ask a New Question
Science
Physics
should the bulb of thermometer be completely immersed in boiling water to measure its boiling point
1 answer
Yes, completely immersed. Think why...
You can
ask a new question
or
answer this question
.
Similar Questions
If a thermometer bulb is not completely immersed in water, what effect will this have on the measured melting point? Will it be
Top answer:
The measured melting point probably will be lower than it should be because not all of the mercury
Read more.
in a hypothetical thermometer, the freezing point of water is marked as -10 and the boiling point is marked at 70. What would be
Top answer:
40 degrees
Read more.
A teacher covered the scale of a mercury thermometer to test the ability of the students to measure the boilling point of
Top answer:
It is not possible to determine the boiling point of the unknown liquid based solely on the options
Read more.
which of the following must be known precisely for the specific heat to be accurate.
Answer a. the mass of the water in the
Top answer:
To accurately calculate specific heat, we must have precise knowledge of the following: a. The mass
Read more.
An ordinary mercury-in-glass thermometer is calibrated. In the ice water bath, the mercury level is 2.45 cm above the bulb. In
Top answer:
---- = 17.75 = 100 C ^ | | | | | | v ^ | | | | -------2.45 cm = 0 C | O bulb So zero is 2.45 cm
Read more.
What effect does lowering the pressure on the surface of water have on the boiling point?
It increases the boiling point It
Top answer:
Raising the pressure increases the boiling point. (The automobile radiator works that way). Lowering
Read more.
Comparing the boiling points of:
A) C3H8 B) C5H12 C) C2H5OH and identify the folowing statements as either True or False:
Top answer:
This should get you started since both A and B are hydrocarbons. C is an alcohol and will exhibit
Read more.
How would you expect the boiling point of methane to compare with the boiling point of water
The boiling point would probably be
Top answer:
The boiling point of methane would likely be different from the boiling point of water because
Read more.
Calculate the correct boiling point for nitrobenzene. Assume that a total immersion thermometer was used. The obs. boiling point
Top answer:
A lot of reading but very well explained and the calculation is at the bottom of the page.
Read more.
Which of the following statements about boiling points are true?
A. The boiling point of 0.1 m NaF(aq) is lower than the boiling
Top answer:
All of these can be answered with delta T = i*Kf*m or i*Kb*m I can help you if you explain what you
Read more.
Related Questions
In which case would recalibrating a thermometer be an important next step in an experiment dealing with boiling points?(1 point)
Two HVAC technicians are discussing the properties of water.Technician A says that if the pressure of water is raised,the
At a certain elevation, the boiling point of water is 98.5°C. How much energy is needed to heat 35.0 mL of water to the boiling
Diethyl ether has a boiling point of 34.5C, and 1-butanol has a boiling point of 117C. Both of these compounds have the same
A thermometer of mass 0.0550 kg and of specific heat 0.837 kJ/kg•K reads 15.0°C. It is then completely immersed in 0.300 kg
why do we add boiling chips or boiling stones before the distillation starts? Boiling chips should never be added to a hot
a student dissolves 1.0mole of sucrose in 1000 grams of water at 1.0atm. Compared to the boiling point of pure water , the
Crude oil pumped out of the ground may be accompanied by the formation of water, a solution that contains high concentrations of
Experimental design: Heat samples of water and ethanol in two separate beakers using a Bunsen burner. Measure the temperatures
What are the temperatures for freezing water and boiling water on the Kelvin temperature scale?
a)273K for freezing water; 373K