CHEMISTRY

If you use a dirty buret, the titrant leaves drops of solution behind as the meniscus descends during delivery of the solution.

The volume actually delivered by the buret will be __________ the volume your readings of the buret scale indicate was delivered


the same as

less than

greater than

impossible to relate to

  1. 👍
  2. 👎
  3. 👁
  1. Wouldn't you think less than?

    1. 👍
    2. 👎
  2. the same as

    1. 👍
    2. 👎
  3. Greater than

    1. 👍
    2. 👎
  4. Less than

    1. 👍
    2. 👎
  5. The true answer is 'less than', submitted that option and it was correct.

    1. 👍
    2. 👎

Respond to this Question

First Name

Your Response

Similar Questions

  1. Chemistry

    IN my experiment, I was doing a qualitative analysis of Group I and II anions using a flowchart. IN the chart I added 5 drops of 0.1M AgNO3 and several drops of 3M HNO3 to 5 drops of solution and found that a precipitate was

  2. acid-base titrations

    For each of the following circumstances, indicate whether the calculated molarity of NaOH would be lower, higher or unaffected. Explain your answer in each case. a.the inside of the pipet used to transfer the standard HCI solution

  3. Chemistry

    A titration setup was used to determine the unknown molar concentration of a solution of NaOH. A .025 M HCl solution was used as the titration standard. The following data were collected. Trial 1 Trial 2 Trial 3 Initial NaOH Buret

  4. Chemistry

    This is a lab called Enthalpy and Entropy of Borax Dissolution and I just can't seem to get the right answers... Please help me fill in the blanks The _____ (acid/HCl?)is placed in the buret and the ____ (base/borax?) is placed in

  1. chem TITRATION

    1. If a student fails to remove a large air bubble in the buret before beginning the titration, what will be the effect on the volume of titrant required to reach the titration endpoint? A. The student will record a volume that is

  2. AP Chemistry

    A 0.250 M NaOH solution was used to titrate a 19.75 mL HI solution. The endpoint was reached after 32.95 mL of titrant were delivered. Find the molar concentration of HI in the original solution.

  3. AP Chemistry

    A 0.3500 MHCl solution was used to titrate a 21.60 mL sodium acetate solution. The endpoint was reached after 25.75 mL of titrant were added. Find the molar concentration of sodium acetate in the original solution.

  4. AP Chemistry

    A 0.2500 M NaOH solution was used to titrate a 16.85 mL hydrofluoric acid solution. The endpoint was reached after 31.20mL of titrant were added. Find the molar concentration of hydrofluoric acid in the original solution.

  1. AP Chemistry

    A 0.500 M HNO3 solution was used to titrate a 21.15 mL KOH solution. The endpoint was reached after 22.30 mL of titrant were delivered. Find the molar concentration of KOH in the original solution.

  2. Chemistry please help

    A 0.200 M NaOH solution was used to titrate a 18.25 mL HF solution. The endpoint was reached after 31.20 mL of titrant were added. Find the molar concentration of the original HF solution.

  3. Chemistry

    A student collected H2 gas in a buret by displacing water at 22.0 °C. The buret could not be submerged deep enough in a water bath to equalize the pressure. The water level in the buret was 18.2 cm above the water level in the

  4. APChem

    If an air bubble passes unnoticed through the tip of a buret during a titration (where a weak nonvolatile acid HA is the analyte) , the calculated molar mass of HA would be too high, too low, or not affected? I thought it would be

You can view more similar questions or ask a new question.