Chemistry

What is the molarity of an Acetic Acid Solution that requires 40.0 ml of 0.100M NaOH to titrate a 20.0ml sample to the end point?
(Balanced equation & solution please! Thanks in advance)

  1. 👍 0
  2. 👎 0
  3. 👁 174
asked by Gage
  1. Refer to your question above for Ca(OH)2 and HCl.

    1. 👍 0
    2. 👎 0
    posted by DrBob222

Respond to this Question

First Name

Your Response

Similar Questions

  1. chemistry

    You were given 25.00 ml of an acetic acid solution of unknown concentration. You find that it requires 29.60 ml of a 0.1050 M NaOH solution to exaclty neutralize this sample. A) What is the molarity of the acetic acid solution? B)

    asked by Rema on October 20, 2011
  2. Chemistry

    In this experiment NaOH is standardized to find out the percent by mass of the acetic acid in a sample of vinegar. A student had not allowed the NaOH pellets to dissolve completely before standardizing it with KHP, but when the

    asked by Sandy on March 29, 2014
  3. Chem

    Please tell me if these are right! 1.How many milliliters of 0.215 M NaOH solution are needed to completely neutralize 2.50 ml of 0.825 M H2SO4 solution? I got 19.2 ml 2. A 10.0-ml sample of vinegar which is an aqueous solution of

    asked by Jessica on December 6, 2010
  4. chemistry

    A 10.0-mL sample of vinegar, which is an aqueous solution of acetic acid, CH3COOH, requires 16.5 XML of a 0.500M NaOH solution to reach the endpoint in a titration (where the moles of acid are equal to the moles of base). What is

    asked by Zarion Gibbs on May 4, 2011
  5. Chemistry

    A 10.0 ml sample of vinegar which is an aqueous solution of acetic acid, requires 16.5ml of a 0.500M NaOH solution to reach the endpoint in a titration (where the moles of acid are equal to the moles of base). What is the molarity

    asked by Brittany on April 19, 2011
  1. Chemistry

    If a 11.0 mL sample of vinegar (aqueous acetic acid ) requires 19.0 mL of 0.500 M NaOH to reach the endpoint, what is the original molarity of the acetic acid solution?

    asked by Erin on October 29, 2012
  2. Chem

    What is the pH of the resulting solution if 30.00 mL of 0.100M acetic acid is added to 10.00mL of 0.100 M NaOH? For acetic acid, Ka=0.000018. I know that NaOH is a strong base and acetic acid is a weak acid. What is the equation:

    asked by Sarah on February 27, 2008
  3. chemistry

    i am given equation CH3COOH + NaOH ---> NaCH3COO + H2O 25ml of acetic acid solution 0.025L 12ml of mid point of titration 1mol of NaOH find molar concentration i use a balanced equation it's a 1:1 ratio finding NaOH molarity =

    asked by unknown on April 12, 2008
  4. chemistry

    Titration was used to determine the molarity of acetic acid in vinegar. A primary standard solution of KHP was used to standardize the NaOH. 1. When performing this experiment, impure KHP was used to standardize the NaOH solution.

    asked by Sandy on March 11, 2014
  5. chemistry

    2. When preparing a NaOH solution, a student did not allow the NaOH pellets to completely dissolve before standardizing the solution with KHP. However, by the time the student reļ¬lled the buret with NaOH to titrate the acetic

    asked by anonymous on March 24, 2014

More Similar Questions