Questions LLC
Login
or
Sign Up
Ask a New Question
Electrical Engineering
Power Systems
Cable Sizing
how to calculate the size of cable for 40kw motor
1 answer
you need the current requirements for that motor, then, use your cable charts to see what cable is safe for that current.
You can
ask a new question
or
answer this question
.
Similar Questions
an electric motor is used to pull a 125 kg box across a floor using a long cable. the tension in the cable is 350 N amd the box
Top answer:
See your previous post for solution.
Read more.
an electric motor is used to pull a 125 kg box across a floor using a long cable. the tension in the cable is 350 N amd the box
Top answer:
Wb = mg = 125kg * 9.8N/kg = 1225N. = Weight of box. Fb = (1225N,0deg.). Fp = Fh = 1225sin(0) = 0 =
Read more.
An electric motor is used to lift a load of bricks through a vertical height of 20m.the tension in the cable attached to the
Top answer:
work = force * distance
Read more.
An electric elevator cable with a motor at the top has a multistrand cable weighing 4.5lb/ft. When the car is at the first
Top answer:
work = integral w dz w = 4.5 (180-z) so work = integral from z = 0 to z = 180 of 4.5 (180-z)dz =
Read more.
An electric motor is used to pull a 125 kg box across a floor using a long cable. the tension in the cable is 350N and the box
Top answer:
To find the distance traveled by the box after the cable breaks until it stops, we need to use the
Read more.
An electric motor is used to pull a 125 kg box across a floor using a long cable. the tension in the cable is 350N and the box
Top answer:
To find the distance the box travels from the moment the cable breaks until it stops, we can use the
Read more.
An electric motor is used to pull a 125 kg box across a floor using a long cable. the tension in the cable is 350N and the box
Top answer:
joe mama joe mama joe mama
Read more.
An elevator (mass 4025 kg) is to be designed so that the maximum acceleration is 0.0700g.
What is the maximum force the motor
Top answer:
I am so sorry but ellll tothero cannot teach so.
Read more.
An elevator (mass 5000 kg) is to be designed so that the maximum acceleration is 0.0620 g. What is the maximum force the motor
Top answer:
To find the maximum and minimum forces the motor should exert on the supporting cable, we need to
Read more.
An elevator (mass 4125 kg) is to be designed so that the maximum acceleration is 0.0400g.
What is the maximum force the motor
Top answer:
max force= mg+ ma I would add in the masses of the maximum number of passengers, that will be what
Read more.
Related Questions
2. At time t =0, the current to the dc motor is reversed, resulting in an angular displacement of the motor shaft given by θ =
a pulley of 5cm radius on a motor is turning at 30 rev/s and slows down uniformly to 20 rev/s in 2s. calculate the angular
Calculate the work done in each of the following situations.
(a) A horse pulls a wagon with a force of 1200 N and moves it 15 m.
A pulley of radius 0.5m, on a motor is turning at 30Rev/s and slows down uniformly in 2.0s.calculate ;(a)the angular
A beam BC and a cable AB support a weight of 1200lbs. The beam weighs 300lbs. Calculate the tensions in the cable and the
Calculate the work done in each of the following situations.
a) A horse pulls a wagon with a force of 1200 N and moves it 15 m.
In a rescue, a 74.1 kg police officer is suspended by two cables, as shown in the figure. Cable A makes an angle θA = 32.0°
skier of mass 79 kg is pulled up a slope by a motor-driven cable.
(a) How much work is required to pull him 80 m up a 30° slope
A cable 45.4 m long is carrying a uniformly distributed load
along its span. If the cable is strung between two posts at the same
A 165.8-N bird feeder is supported by three cables as shown in the figure below. Find the tension in each cable.
left cable - ???
