physics
posted by Dog .
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E .

physics 
faryia
E4_1?
All the bars in truss ABC have constant cross section and are made of a homogeneous linear elastic material. Under the effect of a 1 kN horizontal load applied at B , the pin at A is observed to displace to the right by 6 cm.
Use the method of joints to obtain the numerical value (in kN) of the axial forces in the bars.
NAB=
kN
unanswered
NBC=
kN
unanswered
NCA=
kN
unanswered
E4_1B
Obtain the numerical value (in kN) of the reactions at the supports.
RAy=
kN
unanswered
RCx=
kN
unanswered
RCy=
kN
unanswered
E4_1C
Obtain the numerical value (in kN/m) of the stiffness of bar CA .
KCA=
kN/m
unanswered
E4_2: SOLVING TRUSSES WITH MATLAB PART 1: SELECT DEGRESS OF FREEDOM
All the bars of the truss in the figure below have a crosssectional area of 10 mm2 . We want to determine the axial forces in each of the bars and the Cartesian components of the reactions at supports C and D using the method of joints.
We will soon use MATLAB to solve this problem, but first we need to identify the "free" and the "constrained" degrees of freedom (DOFs) of the joints of the truss. Because this is a 2D problem in the xy plane, each joint of the truss can only have two (Cartesian) DOFs (i.e., the joint can move only along x and along y). Some joints are hinges directly attached to the wall. These joint/hinges (like joint C in the example above) cannot freely move when the truss is loaded, because the wall prevents it: these DOFs are "constrained". In contrast, a joint like A is not attached directly to the wall, so it is free to move in both Cartesian directions: its DOFs are unconstrained or "free".
For each component below, select "Free" if it is unconstrained and "Fixed" if it is constrained.
Joint A , x component
FreeFixed
Joint A , y component
FreeFixed
Joint B , x component
FreeFixed
Joint B , y component
FreeFixed
Joint C , x component
FreeFixed
Joint C , y component
FreeFixed
Joint D , x component
FreeFixed
Joint D , y component
FreeFixed
Joint E , x component
FreeFixed
Joint E , y component
FreeFixed 
physics 
AMK
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E .
We start with the classification of the degrees of freedom as "free" or "constrained".
From the geometry of the truss, we see that we have:
Free DOF x and y at B, C, and D.
Constrained DOF x and y at A and E .
Question 1: Use MATLAB to find the axial forces in the bar.
Order the vector {X} of unknown axial forces in the bars as:
Respond to this Question
Similar Questions

PLEASE REPLY
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
MIT LAB PLEASE HELP
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
SIMONSAY, PLEASE HELP
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
Physics
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
Mechanical Engineering
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
Mechanics
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
MATLAB
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
Physics
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . We start with the classification of the degrees … 
physics
A vertical load W is applied to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A and E in terms of the magnitude of the applied load, W. Use … 
physics
A load W=2 kN is applied vertically to joint C of truss ABCDE as indicated. You will use the method of joints to obtain the axial forces in the bars and reactions at the supports A, E . E4_1?