posted by .

how do i calculate the NaOH molarity from a titration of KHP and NaOH after preparing KHP to standardise NaOH. KHP mass was 2.0378g dissoveld in distilled water to fill up a 100ml volumetric flask and only 10ml of this solution was used to in titration

  • chemistry -

    mols KHP = grams/molar mass
    You took 10mL from 100 so you took 1/10 of those mols to titrate.
    Then mols NaOH = same as mols in the titrated KHP.
    M NaOH = mols NaoH/L NaOH.

Respond to this Question

First Name
School Subject
Your Answer

Similar Questions

  1. chemistry

    The KHP used in the titration with NaOH was contaminated with sodium hydrogen phyhalate (NaHC8H4O4), but you didn't know it. State the effect of the final result (falsely high, falsely low, or unaffected) Explain. thanks These problems …
  2. chemistry

    If the stockroom fails to dry the KHP to remove the waters of hydration, the student's calculated concentration for the standardized base will be: ____________ (low, high, or unaffected) A drop of NaOH is hanging from the buret tip …
  3. chemistry

    KHP is a monoprotic acid with a molar mass of 204.22 g/mol. The titration data are as following. The average concentration of NaOH solution is M. 1 2 3 mass of KHP (g) 2.789 2.543 2.612 vol NaOH used (mL) 27.77 23.22 27.12 You didn't …
  4. chemistry

    calculate the mass of NaOH neded to prepare 500mL of a 0.10 M solution. I'm pretty sure the answer is 2g, but how do I get to that?
  5. Inorganic chemistry

    Potassium hydrogen phthalate (molar mass = 204.2g/mol) is used to standardize sodium hydroxide. If 26.37 mL of NaOH(aq) is required to titrate 0.7719g KHP to the equivalence point, what is the concentration of the NaOH(aq) (26.37 mL …
  6. Analytical Chemistry

    How do I find the mass of KHP? 0.5050 grams of KHP was used and placed into a 250mL volumetric flask and diluted to the mark with distilled water. 50.00mL of this KHP solution was placed in a 250mL beaker. It took 14.75mL of 0.0067M
  7. chemistry

    Titration was used to determine the molarity of acetic acid in vinegar. A primary standard solution of KHP was used to standardize the NaOH. 1. When performing this experiment, impure KHP was used to standardize the NaOH solution. …
  8. science-chemistry

    We performed a titration with NaOH solution with KHP. Now I need to calculate the average molarity of NaOH based on this data Weight of khp= 0.1083 g Volume of naoh = 6.4 ml Then if i get this how do i get the molarity of ch3cooh totrated …
  9. chem

    A .7567 impure KHP was dissolved in water. 26.7 ml of standardized 0.068 M NaOH was used to achieve a phenolphthalein end point. The stoichiometric ratio between KHP and NaOH is 1:1. What is the percent by mass of KHP in the sample?
  10. Chemistry

    Calculate the theoretical amount of .5M NaOH that it would take to neutralize approx. 2.0 g KHP. KHP is a monoprotic acid, the molar mass of KHP is 204.22 g/mol and the molar mass of NaOH is 40.00 g/mol. Answer in terms of mL. I converted …

More Similar Questions