# Chemistry

posted by .

I really don't know how to approach this problem and I really need help.

Using the average molarity of your initial acetic acid solutions, the initial volumes, and the volume of NaOH added to reach the equivalence point, calculate the [C2H3O2-] concentration at the equivalence point.

# of Trials Initial V(HC2H3O2) Vol(NaOH) pH(equiv. Pt.) [OH-] C2H3O2-](eq. Pt.)
Trial 1: 31.1 21.8 7.27 1.86E-007
Trial 2: 30.1 21.7 7.10 1.26E-007
Trial 3: 29.9 24.7 7.13 1.35E-007

• Chemistry -

I have tried to make sense of this post and can't. It isn't your fault; the problem is that the board doesn't recognize spaces over one(1). You also run into problems if the amount of material covers more than one line. I suggest you do this vertically instead of horizontally. This is really a simpler problem and I can help if we can get the data straight.
Example:
Trial 1
volume acetic acid =
volume NaOH =
etc.
I am a little confused by the following:
initial volume HC2H3O2. Is that what you started with?
How much of this is your calculation versus experimental observation?
I don't get the 1.86E-007, especially the 007 part.

## Similar Questions

1. ### chemistry

Could someone help me with this please? In chemistry, we did a lab in which he put brands of commerical vinegar in a microplate. We put in 10 drops of each vinegar in each plate thinger then we added 1 drop of phenolphthalein and then
2. ### chemistry

I am confused on how to do the last question. Calculate molarity of HCl from the volumes of acid and base at the equivalence point and the molarity of NaOH from the titration curve. (M of Acid)x(v of acid)= (m of base)x(v of added …
3. ### Chemistry

Hello, I have a question that reads: Using the average molarity of your initial acetic acid solutions, the initial volumes, and the volume of NaOH added to reach the equivalence point, calculate the [C2H3O2-] concentration at the equivalence …
4. ### Chemistry

In this case, the inflection point, and equivalence, occurs after 23.25mL of 0.40 M NaOH has been delivered. Moles of base at the equivalence point can be determined from the volume of base delivered to reach the equivalence point …
5. ### Chemistry lab

1) Using the 1st equivalence point from part a calculate the molarity of the phosphoric acid. Molarity of NaOH = .1523 M Volume of phosphoric acid used 10.0mL Volume at equivalence point 7.410 mL and 14.861 mL 2) Using the 2nd equivalence …
6. ### chemistry 2

Titration of 50.0 mL of acetic acid reaches equivalence after delivery of 22.5mL of standardized NaOH 0.21 M. What is the initial concentration of acetic acid and what is the pH of the solution?
7. ### Chemistry

Titration of 50.0 ml of acetic acid reaches equivalence after delivery of 22.5 ml of standardized NaOH 0.21 M. What is the initial concentration of acetic acid and what is the pH of the solution?
8. ### Chemistry 12

Hi, I did the acid-base titration lab with HCl and 0.5M NaOH. I need to calculate the moles of NaOH from molarity of NaOH and the average volume used. My English isn't good but is it asking me to find the moles of NaOH using the molarity …
9. ### Chemistry

The data below was collected while performing a titration of acetic acid (in vinegar) to determine its concentration using sodium hydroxide. 150 ml of vinegar with unknown molarity 45.5 ml of .5 M NaOH was added to reach equivalence …
10. ### chemistry

Consider the titration of 40.0 mL 0.250 M ethylamine, C2H5NH2, with 0.350 M HCl. Determine each of the following and sketch the titration curve. Kb of ethylamine = 5.6x 10-4 a. The volume of added acid required to reach the equivalence …

More Similar Questions