Wednesday
October 1, 2014

Search: pulley

Number of results: 906

Physic
A block (mass 2.4 kg) is hanging from a massless cord that is wrapped around a pulley -3 2 (moment of inertia of the pulley = 1.3 x 10 kgm ), as the drawing shows. Initially the pulley is prevented from rotating and the block is stationary. Then, the pulley is allowed to ...
February 4, 2013 by Jess

physics
A block (mass = 2.9 kg) is hanging from a massless cord that is wrapped around a pulley (moment of inertia = 1.2 x 10-3 kgm2), as the figure shows. Initially the pulley is prevented from rotating and the block is stationary. Then, the pulley is allowed to rotate as the block...
November 3, 2010 by danica

college trig
find the radius of a pulley if rotating the pulley 108.03 degrees raises the pulley 37.3mm
July 15, 2013 by brandi

Help Math
A circular pulley with a radius of 10 cm is turning at 12 revolutions per minute. How fast is a point on the edge of the pulley rising when it is 5 cm higher than the center of the pulley?
January 9, 2012 by Jordan

math (Calculus)
A circular pulley with a radius of 10 cm is turning at 12 revolutions per minute. How fast is a point on the edge of the pulley rising when it is 5 cm higher than the center of the pulley?
January 9, 2012 by Jordan

Physics, please help me today.
four pulleys are connected by two belts. Pulley A (radius 15cm) is the drive pulley and it rotates at 10 rad/s. Pulley B (radius 10 cm) is connected by belt 1 to pulley A. Pulley B' (radius 5cm) is concentric with pulley B and is rigidly attached to it. Pulley C (radius 25cm) ...
November 17, 2006 by Dawn

pulley and rotation
Two masses, mA = 35.0 kg and mB = 42.0 kg, are connected by a rope that hangs over a pulley (as in the figure). The pulley is a uniform cylinder of radius 0.50 m and mass 4.8 kg. Initially mA is on the ground and mB rests 2.5 m above the ground. If the system is released, use ...
March 11, 2010 by Anonymous

Physics
A special pulley has two discs with radii R1 = .8 m and R2 = .35 m. A rope from the R2 disc connects the pulley to a wall and a rope from the R1 disc connects the pulley to a hanging mass. The axle is frictionless. The total mass of the pulley is 15 kg. a. If the hanging mass ...
April 23, 2012 by Charlie

Physics
A pulley system os being used to raise a load. The rope begins at the ceilings, goes down, round a pulley on the load, up to a pulley on the ceiling, back down and around a second pulley on the load, and up to a sheave (a motor driven pulley) on the ceiling. The rope is ...
July 15, 2012 by Alex

physics (tension in strin and acceleration of syst
two bodies of 9kg and 5.7kg are attached with ends of a string which passes over a pulley so that both bodies move vertically starting from rest at equal heights,lighter body hits pulley in 1.2sec.find length of string and speed with which it hits pulley.diameter of pulley is ...
August 21, 2011 by ahsan asghar

physics
A 15.0 kg mass and a 10.0 kg mass are suspended by a pulley that has a radius of 10.0 cm and a mass of 3.0 kg. The cord has negligible mass and causes the pulley to rotate without slipping. The puller is frictionless and may be treated as a uniform solid cylinder. Note that ...
June 2, 2011 by Samantha

physics
Consider the system shown in the figure below with m1 = 30.0 kg, m2 = 13.7 kg, R = 0.110 m, and the mass of the pulley M = 5.00 kg. Object m2 is resting on the floor, and object m1 is 4.60 m above the floor when it is released from rest. The pulley axis is frictionless. The ...
May 14, 2011 by mimi

Physics
A 3.30-kN piano is lifted by three workers at a constant speed to an apartment 28.8 m above the street using a pulley system fastened to the roof of the building. Each worker is able to deliver 197 W of power, and the pulley system is 75.0% efficient (so that 25.0% of the ...
June 17, 2012 by Kristin

math
the constant angular acceleration of pulley is 4rad/s2, angular speed 3 rad/s, determine the radius of pulley if the total acceleration of a print on the rim of the pulley is 3.5m/s2
July 31, 2012 by ajay

Physics
A pulley is holding two masses-0.5 kg and 2.0 kg. The system is in static equilibrium; the pulley is frictionless; the string is massless. What is the tension of the string holding the pulley?
October 20, 2010 by Lynn

Physics
An object (m=2.85 kg) is attached to a disk-shaped pulley. The diameter of the pulley is 0.242 and its weight is 7.272 N. Suppose the object is allowed to fall (a) What is its linear acceleration? (b) What is the angular acceleration of the pulley? (c) How far does the bucket ...
November 27, 2012 by Hank

Physics
Consider the system shown in the figure with m1 = 25.00 kg, m2 = 10.20 kg, R = 0.18 m, and the mass of the uniform pulley M = 5.00 kg. Object m2 is resting on the floor, and object m1 is 4.00 m above the floor when it is released from rest. The pulley axis is frictionless. The...
April 8, 2009 by Chris

Physics
The two blocks in the figure are connected by a massless rope that passes over a pulley. The pulley is 17 in diameter and has a mass of 1.9 . As the pulley turns, friction at the axle exerts a torque of magnitude 0.40 . If the blocks are released from rest, how long does it ...
February 21, 2011 by Saif sidd

math
A pulley whose diameter is 9 inches is connected by a belt to another pulley whose diameter is 6 inches. If the larger pulley runs at 1200 revolutions per minute, at how many revolutions per minute does the smaller pulley run? a. 800 b. 1080 c. 1600 d. 1800 e. 2000 please ...
April 23, 2014 by thomas

physics
A pulley rotating in the counterclockwise direction is attached to a mass suspended from a string. The mass causes the pulley's angular velocity to decrease with a constant angular acceleration α = -2.2 rad/s2. If the pulley's initial angular velocity is ω = 5.37 rad...
November 4, 2010 by aok

Science
To lift a load to the roof, you apply 21 N of force to a pulley. The pulley applies 21 N of force to the load. What is the mechanical advantage of the pulley? A.0 B.1 C.40 D.21
May 21, 2014 by Shelin

Physics please help! check if its correct
A 3.00 kg stone is tied to a thin, light wire wrapped around the outer edge of the uniform 8.00 kg cylindrical pulley. The inner diameter of the pulley is 60.0 cm, while the outer diameter is 1.00 m. The system is released from rest, and there is no friction at the axle of the...
February 26, 2012 by Brit

physics
Two blocks are connected by a massless rope that passes over a pulley. M1= 2 kg and M2= 4 kg. The pulley is 12cm in diameter and has a mass of 2kg. As the pulley turns, friction at the axle exerts a torque of magnitude 0.5 Nm. if the blocks are released from rest, how long ...
December 1, 2010 by Blanche

PHYSICS
A block of mass 0.86 kg is suspended by a string which is wrapped so that it is at a radius of 0.061 m from the center of a pulley. The moment of inertia of the pulley is 4.6010-3 kgm2. There is friction as the pulley turns. The block starts from rest, and its speed after it...
October 21, 2012 by Emily

Physics
The two blocks in the figure below, m1 = 1.2 kg and m2 = 4.8, are connected by a massless rope that passes over a pulley. The pulley is 12 cm in diameter and has a mass of 2.0 kg. As the pulley turns, friction at the axle exerts a torque of magnitude 0.38 Nm. If the blocks ...
November 21, 2012 by Alex

Physics
Two blocks hang from strings going around pulleys of different diameter that are connected, as shown in the figure. The large pulley has a radius of R = 9.0 cm and and the small pulley has a radius of r = 2.3 cm. The mass of the block that hangs from the small pulley is m = 3....
February 3, 2013 by Anonymous

physics
A rope goes over a circular pulley with a radius of 6.3 cm. If the pulley makes four revolutions without the rope slipping, what length of rope passes over the pulley?
January 5, 2011 by melissa

Physics
A rope goes over a circular pulley with a radius of 5.5 If the pulley makes 6 revolutions without the rope slipping, what length of rope passes over the pulley?
June 18, 2013 by Anonymous

physics
A block of mass 0.74 kg is suspended by a string which is wrapped so that it is at a radius of 0.060 m from the center of a pulley. The moment of inertia of the pulley is 0.0061 kgm2. There is friction as the pulley turns. The block starts from rest, and its speed after it ...
February 11, 2014 by John

physics
A block of mass 0.74 kg is suspended by a string which is wrapped so that it is at a radius of 0.060 m from the center of a pulley. The moment of inertia of the pulley is 0.0061 kgm2. There is friction as the pulley turns. The block starts from rest, and its speed after it ...
February 12, 2014 by Danny

Help - physics
A block of mass 0.74 kg is suspended by a string which is wrapped so that it is at a radius of 0.060 m from the center of a pulley. The moment of inertia of the pulley is 0.0061 kgm2. There is friction as the pulley turns. The block starts from rest, and its speed after it ...
February 12, 2014 by Danny

physics
An Atwood's machine consists of blocks of masses m1 = 13.0 kg and m2 = 19.0 kg attached by a cord running over a pulley as in the figure below. The pulley is a solid cylinder with mass M = 7.30 kg and radius r = 0.200 m. The block of mass m2 is allowed to drop, and the cord ...
November 9, 2011 by Anonymous

Physics helppp
In the figure below, three ballot boxes are connected by cords, one of which wraps over a pulley having negligible friction on its axle and negligible mass. The masses are mA = 30.0 kg, mB = 40.0 kg, mC = 28.0 kg. The image is a horizontal pulley, with mass mA on the left, and...
July 14, 2010 by Sam

physics
An Atwood Machine has a pulley of radius Rpulley = 0.25m, and mass Mpulley = 6.0 kg with two blocks with masses m1 = 5.0 kg, and m2 = 10.0 kg. Treat the pulley as a uniform disk. a) Find the acceleration of each block. b) Find the angular acceleration of the pulley. c) Find ...
December 11, 2006 by nicole

Thermo engineering
The driveshaft of a buildings air-handling fan is turned at 300 RPM by a belt running on a 0.3-m-diameter pulley. The net force applied by the belt on the pulley is 2000 N. determine the torque applied by the belt on the pulley, in N.m, and the power transmitted, in kW.
May 10, 2011 by Justin

physics
A pulley is suspended by a Cord (C). on one end of the pulley there is a 1.2 kg block and on the other is a 3.2 kg block.Determine the tension in this cord after the masses are released and before one hits the ground. Ignore the mass of the pulley and cords
February 14, 2013 by Anonymous

dynamics
13. The constant angular acceleration of a pulley is 4 rad/s2 and its angular speed its 3 rad/s. Determine the radius of the pulley if the total acceleration of a print on the rim of the pulley is 3.5m/s2.
August 3, 2012 by shivankar

college physics
an atwood machine is constructed by mounting a well-lubricated pulley (not necessarily a ring/disc), whose radius is 6.00cm on an axle and passing a rope over the pulley. Each end of the rope is attached to a different mass of 3.0 kg and 2.0kg so they both hang vertically. ...
June 25, 2013 by kim

Physics
Two masses are suspended from a pulley as shown in the figure . The pulley itself has a mass of 0.30 kg, a radius of 0.20 m, and a constant torque of 0.30 m \cdot N due to the friction between the rotating pulley and its axle. What is the magnitude of the acceleration of the ...
November 28, 2010 by Garry

Physics
Two masses are suspended from a pulley as shown in the figure . The pulley itself has a mass of 0.30 kg, a radius of 0.20 m, and a constant torque of 0.30 m \cdot N due to the friction between the rotating pulley and its axle. What is the magnitude of the acceleration of the ...
November 28, 2010 by Stacy

physics
Two masses are suspended from a pulley as shown in the figure below (the Atwood machine). The pulley itself has a mass of 0.20 kg, a radius of 0.15 m, and a constant torque of 0.35 mN due to the friction between the rotating pulley and its axle. What is the magnitude of the ...
January 9, 2011 by melissa

physics
Two masses are suspended from a pulley as shown in the figure below (the Atwood machine). The pulley itself has a mass of 0.20 kg, a radius of 0.15 m, and a constant torque of 0.35 mN due to the friction between the rotating pulley and its axle. What is the magnitude of the ...
January 9, 2011 by lissa

physics
Two masses are suspended from a pulley as shown in the figure below (the Atwood machine). The pulley itself has a mass of 0.20 kg, a radius of 0.15 m, and a constant torque of 0.35 mN due to the friction between the rotating pulley and its axle. What is the magnitude of the ...
January 9, 2011 by i need help please!

physics
One end of a light spring with force constant 300 N/m is attached to a vertical wall. A light string is tied to the other end of the horizontal spring. The string changes from horizontal to vertical as it passes over a solid pulley of diameter 6.00 cm. The pulley is free to ...
November 30, 2009 by caroline

Physics
Note: The left-hand mass is equal to the sum of the other two masses. A massless pulley is attached to the ceiling,in a uniform gravitational field, and rotates with no friction about its pivot. Another massless pulley is attached to the end of the cord on the right and ...
October 1, 2013 by DW

physics
block 1 has mass m1 = 480 g, block 2 has mass m2 = 540 g, and the pulley is on a frictionless horizontal axle and has radius R = 5.2 cm. When released from rest, block 2 falls 76 cm in 5.2 s (without the cord slipping on the pulley). What is the pulley's rotational inertia? ...
April 1, 2013 by ANS

physics
block 1 has mass m1 = 480 g, block 2 has mass m2 = 540 g, and the pulley is on a frictionless horizontal axle and has radius R = 5.2 cm. When released from rest, block 2 falls 76 cm in 5.2 s (without the cord slipping on the pulley). What is the pulley's rotational inertia? ...
April 2, 2013 by Ashley

physics
The figure below shows two objects with masses m and M which are connected with a taut string running over a pulley. The pulley rotates without friction. The two masses are given as M = 393 g and m = 181 g. A second taut string connects the heavier object vertically from the ...
September 27, 2009 by m2a2

physics
"By means of a rope, whose mass is negligible, two blocks (mass: 11kg and 44 kg) are suspended over a pulley. The pulley can be treated as a uniform solid cylindrical disk. The downward acceleration of the 44 kg block is observed to be exactly one half the acceleration due to...
April 1, 2011 by Seth

physics
"By means of a rope, whose mass is negligible, two blocks (mass: 11kg and 44 kg) are suspended over a pulley. The pulley can be treated as a uniform solid cylindrical disk. The downward acceleration of the 44 kg block is observed to be exactly one half the acceleration due to ...
April 3, 2011 by Seth

Physics
A cable passes over a pulley. Because of friction, the tension in the cable is not eh same on opposite side of the pulley. The force in one side is 110 N, and the force on the other side is 100 N. Assume that the pulley is a uniform disk of mass 2.1kg and radius 0.21. ...
October 15, 2010 by Rod

Physics
The pulley system shown in the figure is used to lift a 37 kg crate. Note that one chain connects the upper pulley to the ceiling and a second chain connects the lower pulley to the crate. Assume that the masses of the chains, pulleys, and ropes are negligible and the crate is...
October 25, 2012 by Andrea

i need help i couldnt figure this out...
A block of mass m = 3 kg is attached to a spring (k = 35 N/m) by a rope that hangs over a pulley of mass M = 6 kg and radius R = 6 cm, as shown in the figure. Treating the pulley as a solid homogeneous disk, neglecting friction at the axle of the pulley, and assuming the ...
April 2, 2011 by samJoint

Physics
A fixed 0.15 kg solid-disk pulley with a radius of 0.065 m is acted on by a net torque of 5.2 mN. What is the angular acceleration of the pulley?
November 3, 2010 by Katherine

Physics
A fixed 0.15 kg solid-disk pulley with a radius of 0.075 m is acted on by a net torque of 6.8 mN. What is the angular acceleration of the pulley?
December 11, 2010 by Angela

physics
A fixed 0.16 kg solid-disk pulley with a radius of 0.070 m is acted on by a net torque of 5.0 m * N. What is the angular acceleration of the pulley?
April 11, 2011 by Dorian

dynamics
the normal acceleration of a particle on the rim of a pulley 10 ft in diameter is constant @ 8000 ft/s^2. determine the speed of the pulley in rpm
February 25, 2013 by fatz

physics
2 masses m1 and m2 are connected at ends of in-extensible string that passes over pulley find acceleration and tension in pulley.
September 14, 2014 by ks

physics help pleease!!
A rope goes over a circular pulley with a radius of 6.3 cm. If the pulley makes four revolutions without the rope slipping, what length of rope passes over the pulley? how can i find distance if the only variable given is radius and revolutions?
January 5, 2011 by lissa

Physics
A massless string runs around two massless, frictionless pulleys, where one pulley is attached to the ceiling, and the other is suspended with a mass m. An object with mass m = 17 kg hangs from one pulley. A force F is exerted on the free end of the string to lift the object ...
November 17, 2009 by Nikita

College Physics
For the system of two crates and a pulley in Figure P9.14, (m1 = 28.5 kg, m2 = 10 kg, mpulley = 8 kg), what fraction of the total kinetic energy resides in the pulley?
October 17, 2011 by Sydney

physical
The pail and its contents have a mass of 60 kg. If the cable is 15 m long, determine the elevation of the pulley for equilibrium. Neglect the size of the pulley at A
October 10, 2012 by taher

Trig
A pulley with a diameter of 24 inches is driven by a belt which is moving 1045 ft/min. How many revolutions per minute are made by the pulley?
March 19, 2013 by Katelyn

Physics
For the system of two crates and a pulley in the figure below, what fraction of the total kinetic energy resides in the pulley? (Assume m1 = 14 kg, m2 = 10 kg and mpulley = 5 kg.) (( o )) | | | | [m1] | [m2]
April 1, 2014 by Sarah

physics
A pulley applies a force of 200 N over a distance of 15 m to raise a 530 N drum 4 meters. Calculate the work output done by the pulley.
May 20, 2014 by Victoria

Physics
The pulley system shown in the figure is used to lift a 52-{\rm kg} crate. Note that one chain connects the upper pulley to the ceiling and a second chain connects the lower pulley to the crate. The crate is rising with an acceleration of 2.5 m/s^2. Determine the tension in ...
March 10, 2012 by JO

Physics-Mechanics
A pulley is massless and frictionless. 3 kg, 2 kg, and 6 kg masses are suspended. What is the tension T1 in the string between the two blocks on the left-hand side of the pulley?
September 24, 2010 by Genevieve

physics
Two masses m and 2m are attached with each other by a rope passing over a frictionless and massless pulley. If the pulley is accelerated upwards with an acceleration a, what is the value of T?
February 1, 2011 by nikhil

Physics 121
The pulley has an inner radius of 0.35m and an outer radius of 0.65m. It has a mass of 1.8kg. A string wrapped around the inner part of the pulley is fastened to the ceiling. A second string wrapped around the outer part of the pulley is fastened to a block. Determine the mass...
May 5, 2012 by Lee

science
You have a pulley 13.9 cm in diameter and with a mass of 1.7 kg. You get to wondering whether the pulley is uniform. That is, is the mass evenly distributed, or is it concentrated toward the center or the rim? To find out, you hang the pulley on a hook, wrap a string around it...
October 22, 2013 by Colin

physics rotations-please help
Two masses, mA = 35.0 kg and mB = 42.0 kg, are connected by a rope that hangs over a pulley (as in the figure). The pulley is a uniform cylinder of radius 0.50 m and mass 4.8 kg. Initially mA is on the ground and mB rests 2.5 m above the ground. If the system is released, use ...
March 11, 2010 by Liz

physics!!
The two masses (m1 = 4.96 kg and m2 = 2.90 kg) in the Atwood's machine shown in the figure below are released from rest, with m1 at a height of 0.800 m above the floor. When m1 hits the ground its speed is 0.203 m/s. Assuming that the pulley is a uniform disk with a radius of ...
October 21, 2012 by Emily

Physic
Ok so this question was posted before but I'm confused by the answer. The problem is: The two masses (m1 = 5.0 kg and m2 = 3.0 kg) in the Atwood's machine shown in Figure 10-23 are released from rest, with m1 at a height of 0.87 m above the floor. When m1 hits the ground its ...
March 8, 2010 by Kelsey

physics
starting from rest s=0,pulley A (rA=50 mm)is given a constant angular acceleration, A=6 rad/s2. Pulley C(rC=150mm) has an inner hub D (rD=75 mm) which is fixed to C and turns with it. What is the speed of block B when it has risen s=6 m ?
August 16, 2011 by lehasa

science
The driving pulley of a motorbike rotates at 3 r/s and has a diameter of 300mm. The pulley exerts an effective force of 2000N at a point on its periphery. Calculate the turning moment and the power in Kw .
March 6, 2013 by leslie

physics
A block of mass m = 2.67 kg is attached to a spring (k = 32.3 N/m) by a rope that hangs over a pulley of mass M = 5.34 kg and radius R = 6.41 cm, as shown in the figure. a) Treating the pulley as a solid homogeneous disk, neglecting friction at the axle of the pulley, and ...
March 30, 2011 by toot

physics
A 2 kg mass on a horizontal friction-free air track is accelerated by a string attached to a 115 kg mass hanging vertically from a pulley as shown. Compare the accelerations when the masses are interchanged, that is, for the case where the 115 kg mass dangles over the pulley, ...
November 19, 2010 by justin

physics
When you want to pull downward to lift something, the main advantage of passing a rope upward and through a single pulley,rather than just up over the branch of a tree ,is that the pulley?
March 7, 2012 by April

science
when you want to pull downward to lift something, the main advantage of passing a rope upward and through a single pulley, rather than just up over the branch of a tree, is that the pulley does what?
July 21, 2012 by kristi

trigonometry
Two pulleys have radii 20cm and 6cm,respectively. The smaller pulley rotates 15 times in 12 seconds. Find the angular speed of each pulley in rad/sec
July 26, 2014 by helpme

physics
A block of mass m = 5 kg is attached to a spring (k = 28 N/m) by a rope that hangs over a pulley of mass M = 7 kg and radius R = 3 cm, as shown in the figure. Treating the pulley as a solid homogeneous disk, neglecting friction at the axle of the pulley, and assuming the ...
March 25, 2011 by Anonymous

physics
A block of mass m = 5 kg is attached to a spring (k = 35 N/m) by a rope that hangs over a pulley of mass M = 7 kg and radius R = 4 cm, as shown in the figure. Treating the pulley as a solid homogeneous disk, neglecting friction at the axle of the pulley, and assuming the ...
April 3, 2011 by Anonymous

Physics 10th Grade
Hi im kinda confused still on Pulley systems and hoping someone can help me out. The two masses (m1 = 5.5kg and m2 = 3.0kg) in the Atwood's machine shown in The Figureare released from rest, with at a height of 0.89m above the floor. When m1 hits the ground its speed is 1.8 m/...
November 5, 2009 by Claire

math
The 2 pulleys in the figure have radii of 15 cm and 8 cm, respectively. The larger pulley rotates 25 times in 36 seconds find the angular velocity of each pulley in radians per second. Find angular velocity of each pulley in radians per second.
December 2, 2010 by confused

maths
A pulley revolving at 200 revolutions per minute has a diameter of 15 inches. It is belted to a second pulley which revolves at 150 revolutions per minute. Find the diameter, in inches, of the second pulley. not just answer, please
August 15, 2013 by Tomas

physics/ torques
A block of mass m = 5 kg is attached to a spring (k = 35 N/m) by a rope that hangs over a pulley of mass M = 7 kg and radius R = 4 cm, as shown in the figure. Treating the pulley as a solid homogeneous disk, neglecting friction at the axle of the pulley, and assuming the ...
April 3, 2011 by HELP!!!!

physics
Spring scale A is attached to the floor and a rope runs vertically upward, loops over the pulley, and runs down on the other side to a 99 N weight as shown (in original problem). Scale B is attached to the ceiling and the pulley is hung below it. What are the readings of the ...
November 20, 2010 by anonymous

Trig
assume a pulley has a radius of 12.96 cm. If it takes 18 seconds for 56 cm of belt to go around the pulley, find the angular velocity in radians per seconds
November 28, 2010 by SK

physics
A pulley system is 76% efficient. If a 9000 kg box is lifted a distance of 8 m by a force of 700 N, how much rope is pulled from the pulley system?
November 8, 2011 by luke

Physics
A pulley system lifts a 500-lb block 1.0 foot with an effort of only 50 lb. If the 50 lb moves 30 feet, calculate the efficiency of the pulley system.
June 18, 2013 by Isis

physics
A 3 lb bucket containing 40 lb of water is hanging at the end of a 20 ft rope that weighs 4 oz/ft. The other end of the rope is attached to a pulley. How much work is required to wind the length of rope into the pulley, assuming that the rope is wound onto the pulley at a rate...
September 21, 2012 by Anonymous

physics
A 4.0 kg pulley of radius 0.15 m is pivoted about an axis through its center. What constant torque is required for the pulley to reach an angular speed of 25 rad/s after rotating 6.0 revolutions, starting from rest?
December 11, 2010 by erik

Math
If the ratio of two pulleys, A and B is 4:3, and pulley B has a length of 13.5 inches, how long is pulley A? [a] inches how do i figure this
May 16, 2008 by LT

Physics
A block of mass m = 3 kg is attached to a spring (k = 28 N/m) by a rope that hangs over a pulley of mass M = 7 kg and radius R = 6 cm, as shown in the figure. Treating the pulley as a solid homogeneous disk, neglecting friction at the axle of the pulley, and assuming the ...
March 27, 2012 by Angelina

Physics
A uniform spherical shell of mass M = 19.7 kg and radius R = 1.62 m rotates about a vertical axis on frictionless bearings. A massless cord passes around the equator of the shell, over a pulley of rotational inertia I = 1.02 kg m2 and radius r = 0.63 m, and is attached to a ...
June 2, 2012 by Rhi

Physics 203
The system shown below is released from rest. The mb = 35 kg block is 2 m above the ledge. The pulley is a uniform disk with a radius of 10 cm and mass M = 5.0 kg. Assume that the string does not slip on the pulley. (a) Find the speed of the 35 kg block just before it hits the...
April 6, 2011 by Kayla

Physics
The equation for the torque is the same as for the pulley. E.g., the puylling force of the quadriceps muscle acts as a pulley around the rotula, so can I calculate as a torque movement, knowing that the T = Nm (f x r). Thank you
September 3, 2010 by Emeric

physics
Two blocks are arranged. The pulley can be considered to be massless, and friction is negligible. M1 is four times more massive than M2. (m1 is on the table and m2 is hanging from the pulley). If the system is released from rest, how far will M1 travel in 0.963 s?
December 4, 2010 by jamie

physics
Two blocks are arranged. M1 is on the table and m2 is hanging from the pulley. The pulley can be considered to be massless, and friction is negligible. M1 is four times more massive than M2. If the system is released from rest, how far will M1 travel in 0.963 s?
December 4, 2010 by helena

physics
The two masses on either side of the pulley, 2.2 kg and 3.6 kg, are each initially 1.8 m above the ground, and the massless frictionless pulley is 4.8m above the ground.What maximum height does the lighter object reach after the system is released? [Hint: First determine the ...
February 14, 2013 by Anonymous

Pages: 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | Next>>

Search
Members