Saturday

October 22, 2016
Number of results: 140

**Science**

What is the rule for combining resistors in series and parallel circuits( combination circuits)?

*October 17, 2007 by Jeni*

**physics**

Given circuits for f and f−1, we can create classical reversible circuits Rf, R−1f, Rf−1, R−1f−1 which are shown in the following figure. (Assume that f is a bijection.)In what sequence shall we apply the above circuits in order to implement a ...

*March 6, 2013 by s*

**science**

how does an electric ciircuit work? Books have been written about electrical circuits, what kinds, specilized circuits, etc. You need to be a little more specific with your question.

*April 23, 2007 by garret*

**Statistics**

An electronic product contains 32 integrated circuits. The probability that any integrated circuit is defective is 0.02, and the integrated circuits are independent. The product operates only if there are no defective integrated circuits. What is the probability that the ...

*February 20, 2014 by Ashley*

**electric circuit**

Some types of fuses used to protect electric meters have resistances of several ohms. Is this objectionable (a) in ammeter circuits and (b) in voltmeter circuits? Why?

*July 29, 2014 by Anne*

**physics**

Design some simple digital circuits based on Boolean expressions. Draw circuits that implement the following Boolean expressions using some combination of AND, OR, NOT, NAND, and NOR gates. - NOT X OR NOT Y OR Z - X OR Y OR NOT Z - NOT X AND Y OR NOT Y AND Z Write a two to ...

*June 10, 2009 by Sandhya*

**physics**

The figure below shows three circuits, each consisting of a switch and two capacitors, initially charged as indicated. Let qL represent the charge on the left-hand capacitor in each circuit. The switches in all circuits are then closed.

*April 9, 2013 by bryan*

**Circuits**

In Circuits lab, we had to construct different types of operational amplifiers. The inverting and summing amplifiers produced similar output voltage to the calculated ones but were not negative. I was just wondering why they didn't reverse the sign in the experiment?

*April 30, 2012 by Ana*

**Circuits**

In Circuits lab, we had to construct different types of operational amplifiers. The inverting and summing amplifiers produced similar output voltage to the calculated ones but were not negative. I was just wondering why they didn't reverse the sign in the experiment?

*April 30, 2012 by Ana*

**physics**

for circuits with either an inductor or capacitor, the current gets out of phase with the voltage. for these circuits how are the frequencies of the current and voltage related?

*March 9, 2012 by fatih*

**Physics- Circuits Current & Voltage Problem**

Please find this question onto y a h o o s e a r c h e n g i n e b y c o p y & p a s t e. Determine... (a) the current in each resistor (Indicate the direction of the current flow through each resistor through the sign of your answer. Take upward current flow as positive.) (b...

*March 29, 2016 by Frustrated College Student*

**Discrete Mathematics**

Consider the complete graph with 5 vertices, denoted by K5. A. Draw the graph. B. How many edges are in K5? How many edges are in Kn? C. Find an isomorphic representation (graph) of K5. Give the isomorphism mappings. D. Does K5 contain Eulerian circuits? (why?) If yes, draw ...

*August 3, 2013 by Joy*

**Math!!**

Christmas lights that stay on when one bulb burns out are wired as parallel circuits. Resistors can be used with parallel electrical circuits to restrict the current flow and produce heat. If the first resistor (R1) = 20 Ohms, the second resistor (R2) = 30 Ohms and the ...

*March 3, 2013 by Urgent math help!!*

**mathematica**

Christmas lights that stay on when one bulb burns out are wired as parallel circuits. Resistors can be used with parallel electrical circuits to restrict the current flow and produce heat. If the first resistor (R1) = 20 Ohms, the second resistor (R2) = 30 Ohms and the ...

*March 3, 2013 by Please Urgent Urgent! math help!!*

**math**

A calculator requires a keystroke assembly and a logic circuit. Assume that 83% of the keystroke assemblies and 92% of the logic circuits are satisfactory. Find the probability that a finished calculator will be satisfactory. Assume independence of keystroke assemblies and ...

*September 24, 2009 by jessica*

**math**

A calculator requires a keystroke assembly and a logic circuit. Assume that 83% of the keystroke assemblies and 92% of the logic circuits are satisfactory. Find the probability that a finished calculator will be satisfactory. Assume independence of keystroke assemblies and ...

*October 1, 2009 by Aleah*

**science**

what does p.c.b stand for when your working with circuits?

*October 1, 2008 by zazi*

**Physics**

How are series and parallel circuits wired?

*May 12, 2008 by Kelly*

**electricity**

closed circuits allow current to flow. b b

*August 23, 2005 by bobpursley*

**digital circuits & systems**

Floating point representaction.

*July 29, 2015 by nakul*

**physics**

What are some examples of real resistors used in circuits?

*July 19, 2011 by Tina*

**digital circuits & systems**

Draw the architecture of a microprocessor and explain it.

*July 29, 2015 by nakul*

**Science - Electric Circuits**

A __________is the flow of _________ along a path?

*March 11, 2008 by Evan*

**Physics **

How are lights in schools usually wired... Series or parallel circuits?

*April 2, 2015 by Anonymous*

**digital circuits & systems**

Explain the method of constructing karnaugh maps.

*July 29, 2015 by nakul*

**Science**

Can you advise me on how to draw electrical circuits for equipment in my room such as my tv and stereo. Thanks

*October 12, 2009 by Lewis*

**ET1210- Dc/Ac Circuits**

When you know the wattage and applied voltage of a light bulb, determine its resistance

*November 21, 2014 by Trena*

**about Engineering**

Electronic and Communication Engineering is mainly Mathematical analysis, implemented in practical circuits. You have to understand higher forms of math, and think in those terms. You have to understand the imperfect models used for systems analysis. You have to understand ...

*May 24, 2007 by bobpursley*

**Physics**

Why is parallel circuit brighter compared to series? ( Only one bulb is present in both circuits) Thanks :)

*August 26, 2012 by Tiffany*

**Electronics/Circuits**

Just a simple one... which symbol should I use to represent a strain gauge on circuit diagram? Thanks

*May 11, 2008 by Jake*

**circuits**

in a parallel RLC circuit you have L=100mH and i= inductor current i=50e^(-4000t)-10e^(-5000t) mA how do you find R and C??

*March 23, 2009 by alice*

**Circuits/physics**

For the element shown below, v(t)=1/2tVolts and i(t) = 12t-4t^2 Amps. (a) Find the instantaneous power p(t) as a function of time. + v(t) - |------| -----| |----- |------| i(t)----->

*August 23, 2009 by Bobby*

**Electrical Circuits**

find the number of free electrons in a copper conductor having a diameter of 0.064 in. and a length of 1000ft.

*November 20, 2011 by Marc Eugene Adriano*

**circuits **

If a series RLC circuit has R = 25 ohm, XL = 50 ohms, and XC = 30 ohms, what will be the total impedance?

*May 30, 2013 by Adam*

**Science(electric circuits)**

What is the conclusion about current in a series electric circuit

*June 12, 2014 by Lesedi*

**Science(electric circuits)**

What is the conclusion about current in a parallel electric circuit

*June 12, 2014 by Lesedi*

**circuits**

Determine the gain in dB for a filter that has an output power of 4.9 W and an input power of 3.6 mW.

*May 30, 2013 by Adam*

**College Physics**

In ordinary laboratory circuits, charges uC (microcoulomb) and nC (nanocoulomb) range are common. How many excess electrons must you add to an object to give it a charge of (a) -2.50 uC (b) -2.50 nC.

*January 21, 2008 by Jen*

**electrical**

The minimum size of electrical cable recomended for use inpower circuits by the NEC in adomestic installation is

*October 31, 2009 by Brannico*

**Science(electric circuits)**

What happaned in the series electric circuit with the one bulb disconnected?please Explain

*June 12, 2014 by Lesedi*

**Science(electric circuits) **

What is the conclusion about the potential difference(voltmeter readings) in a series electric circuit

*June 12, 2014 by Lesedi*

**Science(electric circuits)**

What is the conclusion about the potential difference(voltmeter readings) in a parallel electric circuit

*June 12, 2014 by Lesedi*

**Physics- Circuits**

At time t=0, a potential difference of 475 V is applied to a coil with an inductance L=0.642 H and a resistance R=36 ohms. How long does it take to reach 20 percent of maximum energy in the inductor?

*April 12, 2008 by Bobby*

**French**

how would you say "the wire through which the electric current flows." wouold it be, Le fils ca le courant electrique couler a travers. Load(as in electricity): A device that transforms electrical energy into other forms of energy. is it, "Charge: un appareil ca transformer l'...

*May 10, 2008 by Slappy*

**circuits**

when a parallel 5k ohm resistor and a 25k ohm resistor have a 10v supply, what is the total power loss?

*March 19, 2013 by Anonymous*

**science**

There are three sources of resistance in a parallel circuit. Two of them are rated at 20 ohms, the other at 10 ohms. What is the circuits total resistance?

*July 5, 2010 by teresa*

**CIRCUITS**

three 20 kilo ohms Resistors R1, R2, and R3 are in Series across an applied voltage of 120 V. What is the voltage drop across each resistor.

*April 12, 2015 by Camille*

**digital circuits & systems**

What do you mean by logic gates? Explain different types of logic gates.

*July 29, 2015 by nakul*

**French/Science**

I know i posted this already but no One really answered how would you say "the wire through which the electric current flows." wouold it be, Le fils ca le courant electrique couler a travers. Load(as in electricity): A device that transforms electrical energy into other forms ...

*May 10, 2008 by Slappy*

**Circuits**

How do I design a low pass filter for an Fc = 4000 Hz and a high pass filter for Fc =2000 Hz?

*April 9, 2012 by Heather*

**Digital Circuits**

which is the primary purpose of a resistor in series with a led being driven by a flip-flop a. Limit voltage b. Limit current c. Limit speed d. Limit power

*May 31, 2015 by Makaila*

**circuits**

A string of five series resistors is connected across a 20 v battery. Zero volts are measured across all the resistors except the second one. What can be wrong with this circuit?

*May 30, 2013 by Adam*

**optical circuits**

Two 1-km fibers are spliced together. Each fiber has a 5-dB loss, and the splice adds 1 dB of loss. If the power entering is 2 m W, then how much power is delivered to the end of this combined transmission line?

*August 31, 2013 by bree*

**Physics - Circuits**

Theres a circuit wired in series that has 4 resistors. 1) 10 ohms 2) 6 ohms 3) 1 ohms 4) 2 ohms Find the potential difference across the 10ohm resistor. Answer in units of V What exactly am i supposed to do to calculate this?

*February 14, 2012 by Anonymous*

**Math, Circuits**

A DC circuit to a specialized of 3000 ohms, a 500 ohms, and 10 000 ohms resistor in series. The series current is 15 mA. Find the Voltage drop across R1.

*April 12, 2015 by Camille*

**Science**

What are fuses and why do they come in different sizes? Fuses are devices placed in electrical circuits as protection for those circuits. They consist of small pieces of wire, sometime as ribbons, and are placed in series with the circuit so that the current passing through ...

*September 28, 2006 by Bethan*

**Physics URGENT**

I did a lab on DC circuits, and we calculated the resistance of multiple resistors in parallel. Resistance of Resistor 1 & 2 = 1000 +/- 5% so R1 =1000+/- 50 R2= 1000 +/1 50 i need to calculate R using the equation... R= 1/R1 + 1/R2 I am confused as to what the uncertainty ...

*February 8, 2010 by Katelynn*

**circuits**

a parallel RLC bandpass circuit with C=10nF and Q=10 has a center frequency of 500 krad/s. Find R,L and the two cutoff frequencies. Can you design this circuit using a cascade connection of two first-order filters seperated by a follower?

*April 20, 2009 by alice*

**circuits**

For the transfer function Tv(s)=[10(s+5)(s+20)]/[(s+1)(s+100)] is this a low-pass, high-pass, bandpass or bandstop function? estimate the corner frequency(ies) estimate the passband gain what is the output if v1(t)=10cos(1000t+45deg) V??

*April 20, 2009 by alice*

**college**

A process for producing electronic circuits has achieved very high yield levels. An average of only 10 defective parts per million is currently produced. 1. What are the upper and lower control limits for a sample size of 100? 2. Recompute the upper and lower control limits ...

*December 8, 2010 by jackie*

**Math**

A process for producing electronic circuits has achieved very high yield levels. An average of only 10 defective parts per million is currently produced. 1. What are the upper and lower control limits for a sample size of 100? 2. Recompute the upper and lower control limits ...

*December 9, 2010 by jackie*

**Introduction to Electricity and Circuits**

A light bulb is wired in series with a 142 resistor, and they are connected across a 120 V source. The power delivered to the light bulb is 22.3 W. What are the two possible resistances of the light bulb?

*February 6, 2011 by Jiji*

**Circuits**

I want to know why is it that a voltage in a capacitor cant change instantaneously and why the current in an inductor cant change instantaneously either. Also, a capacitor stores energy, like a battery, right? Why is it that it can't be used to power, say, and electric train ...

*March 10, 2012 by Tina*

**Physics**

Hey all. I have to find Thevenin’s UTHEV and RTHEV, which can replace the circuit found here: img24.imageshack.us/img24/1723/thevenin.jpg I can do it for small circuits, but this one confuses me a bit. Hope you can get me goig. Thank you very much.

*March 14, 2009 by Muusen*

**computers**

which set of terms below correctly pairs a generation of computers with key innovation associated with it? a. 2nd generation/ intergrated circuits b. 3rd generation/programming languages c. 4th generation/ operating systems d. 5th generation/artificial intelligence

*November 12, 2007 by holli*

**ET1210-Dc/Ac Circuits**

if a certain number of equal resistors are wired in series across a certain voltage source, determine how much voltage is across each resistors.

*November 21, 2014 by patrena *

**Physical Science, ipc**

Which can you do to reduce the power consumption in your home? ________________________________________ A. Add more circuit breakers. B. Wire more parallel circuits. C. Replace 75-watt light bulbs with 40-watt light bulbs.

*July 15, 2010 by Superman*

**chemistry**

Silicon for computer chips is grown in large cylinders called “boules” that are 300 mm in diameter and 2 m in length,as shown.(Figure 1) The density of silicon is 2.33 g/cm3. Silicon wafers for making integrated circuits are sliced from a 2.0 m boule and are typically 0.75 mm ...

*September 18, 2014 by Anonymous*

**current physics**

when dealing with circuits, and you say "the voltage across the battery" and "a current through the battery" what do the words across and through mean.

*February 5, 2009 by Anonymous*

**Physics**

Your lab partner says that a battery provides not a source of constant current, but a source of constant voltage. Do you agree or disagree and why? Also I am really confused with series and parallel circuits like when voltage, current, and resistance increase and decrease

*April 14, 2012 by rebekah*

**Physics help please!**

Hi all. I posted earlier but I'm still stuck on part of this problem. I thought that statements 2 and 3 were correct below. But I got the problem wrong. Any help would be great! Can the voltage across any of the three components in the R-L-C series circuit ever be larger than ...

*March 3, 2012 by Jim*

**internationa business operations management**

As the production manager for an electronic circuit company you have encountered the following situation. Part 1 A process for producing electronic circuits has achieved very high yield levels. An average of only 10 defective parts per million is currently produced. 1. What ...

*August 19, 2010 by lisette*

**physics-series and parellel circuits**

I'll try to explain the schmatic drawing... a 120V battery, total of 12A, leads into a 8ohm resistor (R1), then breaks off into two parallel lines, R2 and R3. the resistance is unknown in R2, and in R3 the resistance is 3 ohms. I need to find the Amperage in R1,R2 and R3 as ...

*May 20, 2012 by Dav e*

**Physics circuit help please!**

Hi all. I posted earlier but I'm still stuck on part of this problem. I thought that statements 2 and 3 were correct below. But I got the problem wrong. Any help would be great! Can the voltage across any of the three components in the R-L-C series circuit ever be larger than ...

*March 3, 2012 by Jim*

**Electricity and Electronics**

A circuit contains twodevices that are connected in parallel. If the resistance of one of these devices is 12 ohms and the resistance of the other devices is 4 ohms, the total resistance of the two devices is? 1/R = 1/R1 + 1/R2 You have R1 and R2. Solve for R. It will be less ...

*June 15, 2006 by jackie*

**Physics**

I am having some problems trying to figure this out. Series circuits I have a "d" battery, a battery holder, 3 different resistors, and a multimeter. How do I put the resistors into a series cicuit? And when I use the multimeter, does it need to be set on ohms or volts? Also, ...

*October 15, 2007 by Soly*

**Science 8th Grade**

Items of clothing rub against each other when they are in a clothes dryer. This can sometimes cause a person to feel a slight shock when he or she removes the clothes from the dryer. This is due to A. The dryer not being grounded B. Static Electricity **** C. Current caused by...

*March 4, 2015 by **

**physics, help with circuits please!**

Can the voltage across any of the three components in the R-L-C series circuit ever be larger than the maximum voltage supplied by the AC source? That maximum voltage is 50 volts in this situation. Also, does Kirchoff's loop rule apply to this circuit? In other words, is the ...

*March 1, 2012 by Jim*

**Physics**

The following circuits represent a logarithm amplifier The output voltage for a log amp with a diode can be determined by the formula below Vout = -(.025V)ln(Vin/IR*R1) , the ln is the natural logarithm of a number. Calculate in a table and sketch the output voltage versus the...

*October 5, 2015 by Megameno*

**Math**

The total resistance of two circuits in parallel is 15 ohms and one circuit has five times the resistance of the other, find the resistance of each circuit. Use 1/R=1/R1+1/R2. R1 and R2 are two individual resistances. a)Find the smaller resistance b)Find the larger resistance

*March 12, 2013 by Megan*

**circuits**

the zero input response of a series RLC circuit with R=80 ohms is V(c)=2e^(-2000t)cos(1000t)-4e^(-2000t)sin(1000t) V for t>0 if the initial conditions remain the same, what is the zero-input response when R=40 ohms

*March 23, 2009 by alice*

**chemistry**

Silicon for computer chips is grown in large cylinders called “boules” that are 300 mm in diameter and 2 m in length,as shown.(Figure 1) The density of silicon is 2.33 g/cm3. Silicon wafers for making integrated circuits are sliced from a 2.0 m boule and are typically 0.75 mm ...

*September 18, 2014 by Anonymous*

**Physics**

Two circuits (the figure below) are constructed using identical, ideal batteries (emf = E ) and identical lightbulbs (resistance = R). If each bulb in circuit 1 dissipates 4.00 W of power, how much power does each bulb in circuit 2 dissipate? Ignore changes in the resistance ...

*February 16, 2012 by jason*

**Physics- Circuits **

In a series RCL circuit the generator is set to a frequency that is not the resonant frequency. This nonresonant frequency is such that the ratio of the inductive reactance to the capacitive reactance of the circuit is observed to be 5.53. The resonant frequency is 220 Hz. ...

*February 24, 2013 by Please HELP *

**Electronics, Physics, Circuits**

Help!! problem about capacitance and inductance... please help me... god bless u all... 1.) A capacitance of 2.0 micro-Farad with an initial charge Qo is switched into a series circuit consisting of a 10.0 ohms resistance. Find Qo if the energy dissipated in the resistance is ...

*October 23, 2009 by Huck*

**Circuits**

A 170 -pF capacitor is connected in series with an unknown capacitance, and as a series combination they are connected to a battery with an emf of 25.0 V. If the 170 -pF capacitor stores 135 pC of charge on its plates, what is the unknown capacitance?

*March 3, 2012 by Susan*

**business**

MGT635-1003B-04 International Business Operations Management Assignment Name: Unit 5 Individual Project Deliverable Length: 6-7 body pages Details: As the production manager for an electronic circuit company you have encountered the following situation. Part 1 A process for ...

*August 15, 2010 by 1SGCalhoun*

**AC circuits**

_____R____________ | | | |+ | XC E1 XL | |- | |+ | | E2 ___________________- Z1 = R= 4 ohms <0 4+-j0 Z2 = XL= 6 ohms <90. 0+j6 Z3 = XC=8 ohms <-90. 0-j8 E1= 10 v < 0. 10 +j0 E2= 40 v < 60. 20+j34.64 Please help me find the current up through R using mesh ...

*December 6, 2015 by TJ*

**Physics**

Two circuits (the figure below) are constructed using identical, ideal batteries (emf = E ) and identical lightbulbs (resistance = R). If each bulb in circuit 1 dissipates 4.00 W of power, how much power does each bulb in circuit 2 dissipate? Ignore changes in the resistance ...

*February 16, 2012 by jason*

**physics**

Each of the four circuits in the drawing consists of a single resistor whose resistance is either R or 2R, and a single battery whose voltage is either V or 2V. The unit of voltage in each circuit is V = 10 V and the unit of resistance is R = 8 Ω. Determine (a) the power ...

*February 14, 2013 by Anonymous*

**Math**

A record playa with a speed of 33 1/3 revolutions per minute, meaning that a needle in a groove around te edge of the record will make 33 and 1/3 circuits around the record in one minute. If the diameter of the record is 40 centimeters, how many centimeters does the needle ...

*July 14, 2016 by Anonymous*

**Math**

A record playa with a speed of 33 1/3 revolutions per minute, meaning that a needle in a groove around te edge of the record will make 33 and 1/3 circuits around the record in one minute. If the diameter of the record is 40 centimeters, how many centimeters does the needle ...

*July 14, 2016 by Anonymous*

**Physics**

I'm totally confused and this is due Monday- We're dealing with electrical circuits and I have to construct a circuit with resistors of 10 Ohms, 20 Ohms, 30 Ohms and 20 Ohms. The total resistance has to be 42 Ohms-Can someone direct me how to even begin to draw this-I know ...

*March 26, 2011 by Aubrey*

**physics**

the table below shows the values of the resistance, capcitive reactance and inductive reactance for five RCL circuits. in which circuit will the voltage lead the current? Resistance capacitive inductive reactance reactance a)50 ohm 288ohm 244ohm b)120 ohm 58 ohm 18 ohm c)...

*May 2, 2010 by seema*

**Circuits Problem (Physics)**

h t t p ://img266.imageshack.us/my.php?image=circuit2ru6.png Given the circuit above: a) Solve for unknown currents. b) What is the potential difference between points a and b? c) If both batteries start with 20 A*h of charge, how long does it take the first of the batteries ...

*April 12, 2008 by Eileen*

**Circuits**

A 3 ohm, a 5 ohm, and a 4 ohm resistor are connected in series across a battery. The voltage drop across a 3 ohm resistor is 6 V. What is the battery voltage?

*April 12, 2015 by Camille*

**Physics**

In the absence of a nearby metal object, the two inductances (LA and LB) in a heterodyne metal detector are the same, and the resonant frequencies of the two oscillator circuits have the same value of 510.0 kHz. When the search coil (inductor B) is brought near a buried metal ...

*March 21, 2013 by Elizabeth*

**Physics**

In the absence of a nearby metal object, the two inductances (LA and LB) in a heterodyne metal detector are the same, and the resonant frequencies of the two oscillator circuits have the same value of 580.0 kHz. When the search coil (inductor B) is brought near a buried metal ...

*April 11, 2013 by Anonymous*

**government**

There are up to _______ judges on an appeals court, only ______ usually hear each case. a. 12;5 b. 12;3 c. 15;5 d. 15;3 I chose d. The book states that, that the United states is divided into 13 courts of appeals. There are 12 geographic circuits, and 1 U.S. Court of Appeals. ...

*April 9, 2015 by Carrie*

**Circuits**

I need to calculate the voltage through the resistor and the voltage through the inductor of an RL series circuit for different frequencies. The voltage of the source is 2.5 V. The inductor is at the top and has an inductance of .200 H and the resistor is at the right with a ...

*March 24, 2012 by Heather*